參數資料
型號： LM1203N
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 音頻／視頻放大
英文描述： RGB Video Amplifier System
中文描述： 1 CHANNEL, VIDEO AMPLIFIER, PDIP28
封裝： PLASTIC, DIP-28
文件頁數： 9/16頁
文件大?。?/td> 559K
代理商： LM1203N
Circuit Description
(Continued)
The ‘‘Drive’’ pin will allow the user to trim the Q9 gain of
each amplifier to correct for differences in the CRT and high
voltage cathode driver gain stages. A small capacitor
(33 pF) at this pin will extend the high frequency gain of the
video amplifier by compensating for some of the internal
high frequency roll off. To use this capacitor and still provide
variable gain adjustment, the 51
X
and series 100
X
pot
should be used with the red and green drive pins. The 91
X
resistor used with the blue drive pin will set the system gain
to approximately 6.2 and allow adjustment of the red and
green gains to 6.2 plus or minus 25%. The video signal at
the collector of Q9 is buffered and level shifted down by
Q10 and Q11 to the base of the output emitter follower Q12.
Between the emitter of Q12 and the video output pin is a
40
X
resistor which was included to prevent spurious oscilla-
tions when driving capacitive loads. An external emitter re-
sistor must be added between the video output pin and
ground. The value of this resistor should not be less than
390
X
or package power limitations may be exceeded when
worst case (high supply, max supply current, max temp) cal-
culations are made. If negative going pulse slewing is a
problem because of high capacitive loads (
l
10 pF), a more
efficient method of emitter pull down would be to connect a
suitable resistor to a negative supply voltage. This has the
effect of a current source pull down when the minus supply
voltage is
b
12V and the emitter current is approximately
10 mA. The system gain will also increase slightly because
less signal will be lost across the internal 40
X
resistor. Pre-
cautions must be taken to prevent the video output pin from
going below ground because IC substrate currents may
cause erratic operation. The collector currents from the vid-
eo output transistors are returned to the power supply at
V
CC
2 pin 23. When making power dissipation calculations
note that the data sheet specifies only the V
CC
1 supply
current at 12V. The IC power dissipation contribution of
V
CC
2 is dependent upon the video output emitter pull down
load.
In applications that require video amplifier shut down be-
cause of fault conditions detected by monitor protection cir-
cuits, pin 11 and the wiper arms of the contrast and bright-
ness controls can be grounded without harming the IC. This
assumes some series resistance between the top of the
control pots and V
CC
.
Figure 7 shows the internal construction of the pin 11 2.4V
reference circuit which is used to provide temperature and
supply voltage tracking compensation for the video amplifier
inputs. The value of the external DC biasing resistors should
not be larger than 10 k
X
because minor differences in input
bias currents to the individual video amplifiers may cause
offsets in gain.
TL/H/9178–7
FIGURE 7. LM1203 Video Input Voltage Reference and Contrast Control Circuits
http://www.national.com
9
相關PDF資料
PDF描述
LM1209 130 MHz/100 MHz RGB Video Amplifier System with Blanking
LM1212N 230 MHz Video Amplifier System with OSD Blanking
LM1229 I2C Compatible CMOS TV RGB and Deflection Processor
LM1229VEC I2C Compatible CMOS TV RGB and Deflection Processor
LM1229YA I2C Compatible CMOS TV RGB and Deflection Processor
相關代理商/技術參數
參數描述
LM1203-N 制造商:TI 制造商全稱:Texas Instruments 功能描述:LM1203 RGB Video Amplifier System
LM1204 制造商:NSC 制造商全稱:National Semiconductor 功能描述:150 MHz RGB Video Amplifier System
LM1204V 制造商:Texas Instruments 功能描述:
LM1205 制造商:NSC 制造商全稱:National Semiconductor 功能描述:130 MHz/85 MHz RGB Video Amplifier System with Blanking
LM1205A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*