<dfn id="m6d1t"><tbody id="m6d1t"><dfn id="m6d1t"></dfn></tbody></dfn>
  • 參數資料
    型號: LKP5741-5D4B1
    廠商: POWER-ONE INC
    元件分類: 電源模塊
    英文描述: 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    封裝: METAL, CASE K02, MODULE
    文件頁數: 13/23頁
    文件大小: 1150K
    代理商: LKP5741-5D4B1
    KP Series
    AC-DC Converters >100 Watt
    Rugged Environment
    Edition 4/4.99
    20/23
    MELCHER
    The Power Partners.
    E Inrush Current Limitation
    The converters may be supplemented by an electronic cir-
    cuit (option E, replacing the standard built-in NTC) to
    achieve an enhanced inrush current limiting function.
    Table 15: Inrush current characteristics with option E
    Characteristics
    LKP
    Unit
    Ui = 230 V AC
    typ
    max
    Iinr p
    Peak inrush current
    21.7
    A
    tinr
    Inrush current duration
    35
    50
    ms
    15
    Ii [A]
    10
    5
    0
    –5
    –10
    0
    20
    40
    60
    80
    t [ms]
    tinr
    Capacitor Ci
    fully charged
    Normal operation
    (FET fully conducting)
    20
    10
    50
    70
    30
    11002
    Fig. 30
    Inrush current with option E, Ui = 230 V AC, Po = Po nom
    Precaution:
    Subsequent switch-on cycles at start-up are limited to
    max. 10 cycles during the rst 20 seconds (cold unit) and
    at continuing on/off (
    TC =95°C) max. 1 cycle every
    8 sec.
    Input
    Filter
    Control
    Converter
    FET
    Ci
    RI
    RS
    Rectifier
    PFC
    -
    Control
    1
    1001
    Fig. 29
    Option E block diagram
    Description of Options
    Table 14: Survey of options
    Option
    Function of Option
    Characteristics
    E
    Electronic inrush current limitation circuitry
    Active inrush current limitation
    P 1, 2
    Potentiometer for fine adjustment of output voltage
    Adjustment range +10/–60% of
    Uo nom excludes R input
    D
    Input and/or output undervoltage monitoring circuitry
    Safe data signal output (Versions D0...DD)
    T
    Current sharing
    Interconnect T-pins if paralleling outputs (3 units max.)
    B1
    Cooling plate
    Replaces standard heat sink, allowing direct chassis-mounting
    1 Option R excludes option P and vice versa.
    2 Option P not available for LKP 5740-6R
    Load
    max. 5 units in parallel connection
    +
    Power bus
    Module
    Vo2–
    Vo2+
    Vo1–
    Vo1+
    T
    Module
    Vo2–
    Vo2+
    Vo1–
    Vo1+
    T
    11037
    Fig. 28
    Paralleling of double output units using option T with
    Power Bus
    Option P Potentiometer
    The potentiometer provides an output voltage adjustment
    range of +10/–60% of
    Uo nom and is accessible through a
    hole in the front cover. This feature enables compensation
    for voltage drops across the connector and wiring. Option P
    is not recommended if units are connected in parallel.
    Option P excludes the R-function. With double output units
    both outputs are affected by the potentiometer setting (dou-
    bling the voltage setting if the outputs are in series).
    If the output voltages are increased above
    Uo nom via R-in-
    put control, option P setting, remote sensing or option T, the
    output current(s) should be reduced accordingly so that
    Po nom is not exceeded.
    Option T Current Sharing
    This option ensures that the output currents are approxi-
    mately shared between all paralleled modules and in-
    creases system reliability. To use this facility, simply inter-
    connect the T pins of all modules. The load leads should
    have equal length and cross section to ensure equal volt-
    age drops. Not more than 3 units should be connected in
    parallel. If output voltage adjustment is requested we
    strongly recommend to use the R-input instead of option P,
    as with option P the required setting accuracy is difcult to
    achieve. The output voltages must be individually set prior
    to paralleling to within a tolerance of 1...2% or the R pins
    should be connected together.
    相關PDF資料
    PDF描述
    LKP5741-5ED6T 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5741-5ERD2B1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5741-5ERD3 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5742-7D4B1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    LKP5742-7ERD1B1 2-OUTPUT 250 W AC-DC PWR FACTOR CORR MODULE
    相關代理商/技術參數
    參數描述
    LKP5741-5R 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 51.36V 5A 280W 15PIN - Bulk
    LKP5742-7R 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 50.5V TO 56.5V 4A 226W 15PIN - Bulk
    LKQ1AF12TV5 制造商:Panasonic Electric Works 功能描述:PCB slim relay,SPNO,TV5,flux pf,5A 12Vdc
    LKQ1AF12TV5T 制造商:Panasonic Electric Works 功能描述:
    LKQ1AF12TV8 制造商:Panasonic Electric Works 功能描述:PCB slim relay,SPNO,TV8,flux pf,8A 12Vdc