- 您現在的位置：買賣IC網 > PDF目錄384593 > LIS3LV02DL (意法半導體) MEMS INERTIAL SENSOR 3-Axis - 【2g/【6g Digital Output Low Voltage Linear Accelerometer PDF資料下載
參數資料
| 型號： | LIS3LV02DL |
| 廠商： | 意法半導體 |
| 英文描述： | MEMS INERTIAL SENSOR 3-Axis - 【2g/【6g Digital Output Low Voltage Linear Accelerometer |
| 中文描述： | MEMS慣性傳感器3軸- 【2克/【6克數字輸出低電壓線性加速度計 |
| 文件頁數： | 16/36頁 |
| 文件大?。?/td> | 248K |
| 代理商： | LIS3LV02DL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Digital Interfaces
LIS3LV02DL
16/36
function, it can hold the clock line, SCL LOW to force the transmitter into a wait state. Data
transfer only continues when the receiver is ready for another byte and releases the data line. If
a slave receiver doesn’t acknowledge the slave address (i.e. it is not able to receive because it
is performing some real time function) the data line must be left HIGH by the slave. The Master
can then abort the transfer. A LOW to HIGH transition on the SDA line while the SCL line is
HIGH is defined as a STOP condition. Each data transfer must be terminated by the generation
of a STOP (SP) condition.
In order to read multiple bytes, it is necessary to assert the most significant bit of the sub-
address field. In other words, SUB(7) must be equal to 1 while SUB(6-0) represents the
address of first register to read.
In the presented communication format MAK is Master Acknowledge and NMAK is No Master
Acknowledge.
5.2
SPI Bus Interface
The LIS3LV02DL SPI is a bus slave. The SPI allows to write and read the registers of the
device.
The Serial Interface interacts with the outside world with 4 wires:
CS
,
SPC
,
SDI
and
SDO
.
Figure 4.
Read & write protocol
CS
is the Serial Port Enable and it is controlled by the SPI master. It goes low at the start of the
transmission and goes back high at the end.
SPC
is the Serial Port Clock and it is controlled by
the SPI master. It is stopped high when
CS
is high (no transmission).
SDI
and
SDO
are
respectively the Serial Port Data Input and Output. Those lines are driven at the falling edge of
SPC
and should be captured at the rising edge of
SPC
.
Both the Read Register and Write Register commands are completed in 16 clock pulses or in
multiple of 8 in case of multiple byte read/write. Bit duration is the time between two falling
edges of
SPC
. The first bit (bit 0) starts at the first falling edge of
SPC
after the falling edge of
CS
while the last bit (bit 15, bit 23, ...) starts at the last falling edge of SPC just before the rising
edge of
CS
.
bit 0
: RW bit. When 0, the data DI(7:0) is written into the device. When 1, the data DO(7:0) from
the device is read. In latter case, the chip will drive
SDO
at the start of bit 8.
bit 1
: MS bit. When 0, the address will remain unchanged in multiple read/write commands.
When 1, the address will be auto incremented in multiple read/write commands.
bit 2-7
: address AD(5:0). This is the address field of the indexed register.
CS
SPC
SDI
SDO
RW
AD5 AD4 AD3 AD2 AD1 AD0
DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0
DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0
MS
相關PDF資料 |
PDF描述 |
|---|---|
| LIS3LV02DL-TR | MEMS INERTIAL SENSOR 3-Axis - 【2g/【6g Digital Output Low Voltage Linear Accelerometer |
| LIS3LV02DQ | MEMS INERTIAL SENSOR 3-Axis - +-2g/+-6g Digital Output Low Voltage Linear Accelerometer |
| LIS3LV02DQ-TR | MEMS INERTIAL SENSOR 3-Axis - +-2g/+-6g Digital Output Low Voltage Linear Accelerometer |
| LJ600600-1 | Class J Fuse Blocks |
| LJ600100-1 | Class J Fuse Blocks |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
| LIS3LV02DLTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DL-TR | 制造商:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR |
| LIS3LV02DQ | 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DQ-TR | 功能描述:加速計 - 板上安裝 INERTIAL SENSOR Lo Vltg 3Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。