參數資料
型號： LIS3DH
廠商： STMICROELECTRONICS
元件分類： 模擬信號調理
英文描述： SPECIALTY ANALOG CIRCUIT, PBGA16
封裝： 3 X 3 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16
文件頁數： 7/42頁
文件大?。?/td> 689K
代理商： LIS3DH
LIS3DH
Terminology and functionality
Doc ID 17530 Rev 1
15/42
3
Terminology and functionality
3.1
Terminology
3.1.1
Sensitivity
Sensitivity describes the gain of the sensor and can be determined e.g. by applying 1 g
acceleration to it. As the sensor can measure DC accelerations this can be done easily by
pointing the axis of interest towards the center of the earth, noting the output value, rotating
the sensor by 180 degrees (pointing to the sky) and noting the output value again. By doing
so, ±1 g acceleration is applied to the sensor. Subtracting the larger output value from the
smaller one, and dividing the result by 2, leads to the actual sensitivity of the sensor. This
value changes very little over temperature and also time. The sensitivity tolerance describes
the range of Sensitivities of a large population of sensors.
3.1.2
Zero-g level
Zero-g level offset (TyOff) describes the deviation of an actual output signal from the ideal
output signal if no acceleration is present. A sensor in a steady state on a horizontal surface
measure 0 g in X axis and 0 g in Y axis whereas the Z axis measure 1 g. The output is
ideally in the middle of the dynamic range of the sensor (content of OUT registers 00h, data
expressed as 2’s complement number). A deviation from ideal value in this case is called
Zero-g offset. Offset is to some extent a result of stress to MEMS sensor and therefore the
offset can slightly change after mounting the sensor onto a printed circuit board or exposing
it to extensive mechanical stress. Offset changes little over temperature, see “Zero-g level
change vs. temperature”. The Zero-g level tolerance (TyOff) describes the standard
deviation of the range of Zero-g levels of a population of sensors.
3.2
Functionality
3.2.1
Normal mode, low power mode
LIS3DH provides two different operating modes respectively reported as normal mode and
low power mode. While normal mode guarantees high resolution, low power mode reduces
further the current consumption.
The table below reported summarizes how to select the operating mode.
Table 9.
Operating mode selection
CTRL_REG1[3]
(LPen bit)
CTRL_REG4[3]
(HR bit)
Operating mode
1
0
Low power mode
0
1
Normal mode
相關PDF資料
PDF描述
LIS3L02AL SPECIALTY ANALOG CIRCUIT, PBGA8
LIS3L02ALTR SPECIALTY ANALOG CIRCUIT, PBGA8
LIS3L02AQ5TR SPECIALTY ANALOG CIRCUIT, PQCC44
LIS3L02AQ5 SPECIALTY ANALOG CIRCUIT, PQCC44
LIS3L02AQ SPECIALTY ANALOG CIRCUIT, QCC44
相關代理商/技術參數
參數描述
LIS3DHHTR 功能描述:ACCELEROMETER 3-AXIS 16LGA 制造商:stmicroelectronics 系列:MEMS 零件狀態:在售 類型:數字 軸:X，Y，Z 加速度范圍:±2.5g 靈敏度（LSB/g）:13157（±2.5g） 靈敏度（mV/g）:- 帶寬:235Hz ~ 440Hz 輸出類型:SPI 電壓 - 電源:1.71 V ~ 3.6 V 特性:溫度傳感器 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:16-LGA 供應商器件封裝:16-CCLGA（5x5） 標準包裝:1
LIS3DHTR 功能描述:加速計 - 板上安裝 MEMS Ultra Low-Power 3-Axes "Nano" RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3DSH 功能描述:加速計 - 板上安裝 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3DSHTR 功能描述:加速計 - 板上安裝 MEMS 3-Axis Nano 1.71 to 3.6V 1.6kHz RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
LIS3L02AL 功能描述:加速計 - 板上安裝 3-axis +/-2g Linear MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*