- 您現在的位置：買賣IC網 > PDF目錄43919 > LIS302DLHTR (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA14 PDF資料下載
參數資料
| 型號： | LIS302DLHTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA14 |
| 封裝： | 3 X 5 MM, 0.80 MM HEIGHT, ROHS COMPLIANT, PLASTIC, LGA-14 |
| 文件頁數： | 8/37頁 |
| 文件大?。?/td> | 673K |
| 代理商： | LIS302DLHTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
Application hints
LIS302DLH
16/37
Doc ID 15797 Rev 1
4
Application hints
Figure 5.
LIS302DLH electrical connection
The device core is supplied through Vdd line while the I/O pads are supplied through
Vdd_IO line. Power supply decoupling capacitors (100 nF ceramic, 10 F Aluminum) should
be placed as near as possible to the pin 6 of the device (common design practice).
All the voltage and ground supplies must be present at the same time to have proper
behavior of the IC (refer to
Figure 5). It is possible to remove Vdd maintaining Vdd_IO
without blocking the communication bus, in this condition the measurement chain is
powered off.
The functionality of the device and the measured acceleration data is selectable and
accessible through the I2C/SPI interface.When using the I2C, CS must be tied high.
The functions, the threshold and the timing of the two interrupt pins (INT 1 and INT 2) can be
completely programmed by the user through the I2C/SPI interface.
4.1
Soldering information
The LGA package is compliant with the ECOPACK, RoHS and “Green” standard.
It is qualified for soldering heat resistance according to JEDEC J-STD-020C.
Leave “Pin 1 Indicator” unconnected during soldering.
Land pattern and soldering recommendations are available at www.st.com.
6
8
13
1
Top VIEW
CS
10uF
Vdd
100nF
GND
Vdd_IO
SDO
SDA/SDI/SDO
IN
T
1
IN
T
2
SCL/SPC
Digital signal from/to signal controller.Signal’s levels are defined by proper selection of Vdd_IO
1
13
8
6
TOP VIEW
X
Z
Y
DIRECTIONS OF THE
DETECTABLE
ACCELERATIONS
相關PDF資料 |
PDF描述 |
|---|---|
| LIS302DL | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS302DLTR8 | SPECIALTY ANALOG CIRCUIT, PQCC14 |
| LIS331ALTR | SPECIALTY ANALOG CIRCUIT, QCC16 |
| LIS331DLF | SPECIALTY ANALOG CIRCUIT, PBCC16 |
| LIS331DLHTR | SPECIALTY ANALOG CIRCUIT, PBCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS302DLTR | 功能描述:加速計 - 板上安裝 MEMS Motion Sensor RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302DLTR8 | 制造商:STMicroelectronics 功能描述:LIS302DLTR8 - Tape and Reel |
| LIS302DLTR-CUT TAPE | 制造商:ST 功能描述:LIS302DL Series 3 Axis ?/? g 3.3 V Digital Output Piccolo Accerometer - LGA-14 |
| LIS302SG | 功能描述:加速計 - 板上安裝 MEMS MOTION SENSOR 3 AXIS +/-2g Piccolo RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS302SGTR | 功能描述:加速計 - 板上安裝 MEMS motion sensor 3-axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。