參數資料
型號： LC8904
廠商： Sanyo Electric Co.,Ltd.
英文描述： Digital Audio Interface Receiver
中文描述： 數字音頻接口接收器
文件頁數： 14/20頁
文件大小： 322K
代理商： LC8904
V flag output selection (DI9)
Source selection (DI10)
Audio data output format setting (DI11, DI12, DI13)
DI4 to DI13 are set to an initial value of low, immediately after the XMODE pin goes from low to high. Since DI0
to DI3 and DI14 to DI15 are unused they can be set to either low or high.
Output
C bits
— This product only supports 32 bits, since it is designed for mode 0 consumer applications.
— In readout when CCB/SUB is low, after the output address is loaded into SWDT, the flag (fixed at the high
level) is output on the fall of XLAT, and then 32 bits of data is output according to SCLK.
— In readout when CCB/SUB is high, after the output address is loaded into DI, the 32 bits of data are output
from DO according to CL while CE is high.
— Since the C bits are not checked for errors, processing is performed after the PLL lock state is detected.
Therefore, data must be read out only after the ERROR pin goes low.
— If a lock error occurs during readout (ERROR = high), the shift register will be reset and all data will become 0
(low). However, while the ERROR pin will also go high on a parity error, this error processing will not be
performed.
— An interval of at least 6 ms or longer must be provided between readout operations.
Subcode Q
— The LC8904Q provides the following two functions for subcode readout:
1. CD subcode interface (CP-2401) is possible
2. Output of subcode Q data with CRC flags included, which corresponds to the CD and MD formats
The microprocessor interface uses the readout function of item 2.
— The subcode Q data, which is reproduced at 1 bit per frame, is input to an 80-bit register and a CRC checking
circuit. After the 96 bits of data have been input, it is loaded into a shift register on the falling edge of
LD/DQSY. The data must be read out after this load operation.
— In readout when CCB/SUB is low, after the output address has been loaded into SWDT, the CRC flags are
output on the falling edge of XLAT. If the CRC flags indicate that the check was OK, a high level is output.
Next, 80 bits of data is output from SRDT according to SCLK. Note that the subcode Q data is updated on
every falling edge of the DQSY signal.
— Readout when CCB/SUB is high is identical to that described in item 3. (See the timing charts for details.)
— The data output from SRDT (DO) has the same order on a per-byte basis, but the bit order within each byte is
LSB first.
— If a lock error occurs between the fall of DQSY and the fall of XLAT, the CRC flags will go low. However, if
a lock error after the fall of XLAT, the CRC flags will not go low, since correct data will be output.
No. 5014-14/20
LC8904Q
DI9
L
H
DOUT/V pin
Data selected by DI7 and DI8
V flag
DI10
L
H
Mode
Digital source
Analog source
DI11
L
L
H
H
H
H
DI12
L
L
L
H
L
H
DI13
L
H
L
L
H
H
16 bits
MSB first
Rear packed
16 bits
MSB first
Front packed
20 bits
MSB first
Rear packed
20 bits
LSB first
Rear packed
20 bits
MSB first
Front packed
20 bits
LSB first
Front packed
DATAOUT
相關PDF資料
PDF描述
LC89051V Digital Audio Interface Receiver(數字音頻接口接收器)
LC8905V Digital Audio Interface Receiver(數字音頻接口接收器)
LC89060 6-Bit Video D/A Converter(6位視頻高速D/A轉換器)
LC89066 6-Bit Video D/A Converter(6位視頻高速D/A轉換器)
LC89080 Video Signal 3-Channel 8-Bit D/A Converter(視頻信號電流輸出3通道8位D/A轉換器)
相關代理商/技術參數
參數描述
LC8904Q 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver
LC89051V 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver
LC89052T 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Digital Audio Interface Receiver
LC89052TA-E 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
LC89052TA-TLM-E 功能描述:音頻發送器、接收器、收發器 RoHS:否 制造商:Cirrus Logic 工作電源電壓:3.3 V, 5 V 電源電流:11.8 mA 通道數量:1 最大工作溫度:+ 70 C 接口類型:I2C, SPI 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-28 封裝:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*