- 您現在的位置：買賣IC網 > PDF目錄358770 > LC876662B (Sanyo Electric Co.,Ltd.) RF CONNECTOR; 50 OHM REVERSE POLARITY BNC MALE RIGHT ANGLE, CLAMP ATTACHMENT FOR RG59 & RG62; *MEETS FCC PART 15.203 REQUIREMENTS* PDF資料下載
參數資料
| 型號： | LC876662B |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | RF CONNECTOR; 50 OHM REVERSE POLARITY BNC MALE RIGHT ANGLE, CLAMP ATTACHMENT FOR RG59 & RG62; *MEETS FCC PART 15.203 REQUIREMENTS* |
| 中文描述： | 8位單片機 |
| 文件頁數： | 4/23頁 |
| 文件大?。?/td> | 655K |
| 代理商： | LC876662B |
LC876694B/78B/62B
No.6843-4/23
(19) Standby function
- HALT mode
HALT mode is used to reduce power consumption. Program execution is stopped. Peripheral circuits still
operate but VFD display and some serial transfer operations stop.
1) Oscillation circuits are not stopped automatically.
2) Release occurs on system reset or by interrupt.
-HOLD mode
HOLD mode is used to reduce power consumption. Both program execution and peripheral circuits are
stopped.
1)CF, RCand crystal oscillation circuits stop automatically.
2) Release occurs on any of the following conditions.
(1) input to the reset pin goes low
(2) a specified level is input at least one of INT0, INT1, INT2
(3) an interrupt condition arises at port 0
-X’tal HOLD made
X’tal HOLD mode is used to reduce power consumption. Program execution is stopped.
All peripheral circuits except the base timer are stopped.
1) CF and RC oscillation circuits stop automatically.
2) Crystal oscillator is maintained in its state at HOLD mode inception.
3) Release occurs on any an any of the following conditions
(1) input to the reset pin goes low
(2) a specified level is input to at least one of INT0, INT1, INT2
(3) an interrupt condition arises at port 0
(4) an interrupt condition arises at the base-timer
(20) Factory shipment
-delivery form QIP100E
(21) Development tools
- Evaluation chip: LC876095
- Emulator: EVA62S + ECB876600 (Evaluation chip board) + SUB876500 + POD100QFP
- Flash ROM version: LC87F66C8A
相關PDF資料 |
PDF描述 |
|---|---|
| LC8766C8A | 8-Bit Single Chip Microcontroller |
| LC876748A | 8-Bit Single Chip Microcontroller |
| LC876748C | CMOS LSI 8 BIT 1 CHIP MICROCOMPUTER |
| LC877248A | 8-Bit Single Chip Microcontroller with 48K-Byte(49151 ×8 bits) ROM and 2048-Byte(2048 ×8 bits) RAM On Chip(8位單片微控制器（帶片上48K（49151 ×8 bit）字節ROM和2048(2048 ×8 bits)字節RAM）) |
| LC8772C8B | 8-Bit Single Chip Microcontroller with 128KB Flash Momory and 2048-Byte RAM On Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC876670B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| LC876678B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single-Chip Microcontroller |
| LC876694B | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single-Chip Microcontroller |
| LC876696A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:8-Bit Single Chip Microcontroller |
| LC876696B | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。