- 您現在的位置：買賣IC網 > PDF目錄358757 > LC587008 (Sanyo Electric Co.,Ltd.) Single-Chip 4-Bit Microprocessors with LCD Driver,2 Kb RAM, and 16 KB ROM on chip(4位單片微控制器（帶LCD驅動器，16K位ROM和2K位RAM）) PDF資料下載
參數資料
| 型號： | LC587008 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Single-Chip 4-Bit Microprocessors with LCD Driver,2 Kb RAM, and 16 KB ROM on chip(4位單片微控制器（帶LCD驅動器，16K位ROM和2K位RAM）) |
| 中文描述： | 單芯片4位的LCD驅動器，2 Kb的RAM和16片KB光盤（4位單片微控制器（帶液晶顯示驅動器，16K的位光盤和2K位RAM）的微處理器） |
| 文件頁數： | 6/29頁 |
| 文件大?。?/td> | 519K |
| 代理商： | LC587008 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Continued from preceding page.
No. 4435-6/29
LC587008, 587006, 587004
Continued on next page.
Pin
I/O
QIP-80
Pin No.
Function
Option
At reset
SO1
SO2
SO3
SO4
7
8
9
I/O
10
N1
N2
N3
N4
39
40
41
42
Output
INT
Input
6
RES
Input
5
TST
Input
43
I/O ports
Function: The same as for pins A1 to A4
Pins SO1 to SO3 area also used for the serial interface.
Use of these pins in serial mode can be selected under program
control.
Pin functions: SO1: Serial input pin
SO2: Serial output pin
SO3: Serial clock pin
The serial clock pin can be switched between internal and external,
and between rising edge output and falling edge output.
Transistors to hold
a low or high level
Selection of either
pull-up or pull-
down resistors
Internal serial clock
divisor selection
I
1/1
II
1/2
III
1/4
The same as for K1
to K4
The output levels on
pins N1 to N4 can be
specified as an option.
Pins N1 to N4
output circuit type:
I
CMOS
II
N-channel
open drain
Pins N1 to N4
output level
I
High level
II
Low level
Transistors to hold
a low or high level
Selection of either
pull-up or pull-
down resistors
Signal conversion
(rising/falling)
selection
*
Only when the
input resistor open
specification is
selected
LCD driver/
general-purpose
output switching
LCD drive type
switching
— STATIC
— 1/2 bias – 1/2
duty
— 1/2 bias – 1/3
duty
— 1/2 bias – 1/4
duty
— 1/3 bias – 1/3
duty
— 1/3 bias – 1/4
duty
General-purpose
output circuit
switching
— CMOS
— P-channel
open drain
— N-channel
open drain
Output latch control
in standby modes
LCD drive
— All segments on
— All segments off
*
: Determined by
mask options
General purpose
outputs
— High level
— Low level
*
: Determined by
mask options
Note: When a
combination of
LCD drive and
general-
purpose
outputs, the
output state is
either:
— All lit/high level
— All off/low level.
These pins go to
the static drive
mode during the
reset period.
Output-only ports
Output pins used to output data from RAM
An alarm signal can be output from pin N4. (Note that this is only
when the N4 output latch is low.)
An alarm signal modulated at 1, 2 or 4 kHz can be output. (These
frequencies are output when 0 is 32.768 kHz.)
A carrier signal can be output from N3. (Note that this is only when
the N3 output latch is low.)
Input ports
External interrupt request inputs
Input pins used to read data into RAM
Input detection can be performed on either rising or falling edges.
Built-in pull-up/pull-down resistors
LSI internal reset input
The reset input level can be selected to be either high or low.
Built-in pull-up/pull-down resistors
Note: The reset pulse must be at least 500 μs.
Test input
QIP80 products: Connect to V
SS
.
Chip products: Leave open or connect to V
SS
.
LCD panel drive/general-purpose output
— LCD panel drive
I
STATIC
II
1/2 bias – 1/2 duty
III
1/2 bias – 1/3 duty
IV
1/2 bias – 1/4 duty
V
1/3 bias – 1/3 duty
VI
1/3 bias – 1/4 duty
Types
I
to
V
can be specified as mask options.
— General-purpose output mode
I
CMOS
II
P-channel open drain
III
N-channel open drain
Types I to III can be specified as mask options.
LCD/general-purpose output control is handled by the segment PLA,
and thus program control is not required.
These pins support output latch control on reset and in standby
states when the oscillators are stopped.
Arbitrary combinations of LCD drive and general-purpose outputs can
be used.
Seg1,
Seg2 to
Seg35
Output
44,
45 to
78
相關PDF資料 |
PDF描述 |
|---|---|
| LC587202A | Single-Chip 4-Bit Micontroller with LCD Driver,512 ×4bit RAM,2K× 16 Bit ROM on chip(單片4位微控制器（帶LCD驅動器，512 ×4位RAM和2K× 16位ROM）) |
| LC5872 | Single-Chip 4-Bit Microprocessors with LCD Driver,1 Kb RAM, and 4 KB ROM on chip(單片4位微控制器（帶LCD驅動器，1K位RAM和4K位ROM）) |
| LC587504A | LC587508A |
| LC58E68 | 4-Bit Microprocessor with Built-in EPROM and LCD Drivers |
| LC58E7008 | On-Chip EPROM Microcomputer 4-Bit Single-Chip Microcontroller with LCD Driver, 16 Kbytes of EPROM and 2Kbits of RAM On-Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC5872 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:On-Chip EPROM Microcomputer 4-Bit Single-Chip Microprocessor with LCD Driver, 12 Kbytes of EPROM and 1Kbits of RAM On-Chip |
| LC587202A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587204A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587206A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
| LC587208A | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:4-Bit Single-Chip Microcontroller LCD Driver ROM:2,4,6,or8 K x 16 bits, RAM:512 x4 bits |
發布緊急采購，3分鐘左右您將得到回復。