- 您現在的位置：買賣IC網 > PDF目錄384589 > LB1962 (友順科技股份有限公司) LINEAR INTEGRATED CIRCUIT PDF資料下載
參數資料
| 型號： | LB1962 |
| 廠商： | 友順科技股份有限公司 |
| 英文描述： | LINEAR INTEGRATED CIRCUIT |
| 中文描述： | 線性集成電路 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 155K |
| 代理商： | LB1962 |
UTC LB1962
LINEAR INTEGRATED CIRCUIT
DESIGN REFERENCE
(1) V
CC
pin
Power supply pin for whole I
C
.
(2) OUT1, OUT2 pins
Single-phase coil output pins.
Bipolar forward or reverse drive output determined by OUT1 or OUT2 high. Built-in regenerative circuit that
regenerates kickback current between lower side NPN outputs if a diode is used for protection against reverse
connection.
(3) IN
–
, IN
+
pins
Hall signal input pins
The Hall signal is amplified into a square wave by the Hall amplifier with hysteresis characteristics of ±3.5 mV
(typ.). The Hall signal amplitude should be 70 mV or more.
(4) CT pin
This pin serves timing capacitor connecting pin between CT and GND.
The capacitor determines timing of the built-in lockup protection circuit for preventing coil burnout when
motor is locked. Once normal motor rotating condition is restored, the automatic recovery circuit will reset itself.
Adjusting the capacitance alters the lockup detection time.
When a 0.47 mF capacitor is connected between CT and GND
Lockup detection time
Lockup protection time/automatic recovery time :approx. 0.16s (output ON)
UTC
UNISONIC TECHNOLOGIES CO., LTD.
4
www.unisonic.com
QW-R109-017,A
:approx. 0.5s
:approx. 1s (output OFF)
Connecting this pin to ground when lockup function is not used
(6) FG pin
Open-collector output pin for rotation frequency detection.
When IN
–
= High and IN
+
= Low, then FG = Low
When IN
–
= Low and IN
+
= High, then FG = High
(7) ST pin and HB pin
ST pin: When input to this pin is High, motor drive is stopped (OUT is high impedance).
HB pin: Hall bias switching pin. At ST pin High input, Hall bias is switched to reduce current drain in fan standby
mode.
If not used, both pins should be open.
(8) Thermal protection circuit
When junction temperature Tj of IC is or over about 150
℃
, output current limiter is activated to protect against
damage.
相關PDF資料 |
PDF描述 |
|---|---|
| LBPC | Precision, 100uA Gain Selectable Amplifier |
| LCE13A | Silicon Avalanche Diodes - 1500W Axial Leaded Transient Voltage Supressors |
| LCE6.5A | Silicon Avalanche Diodes - 1500W Axial Leaded Transient Voltage Supressors |
| LCE8.0A | Silicon Avalanche Diodes - 1500W Axial Leaded Transient Voltage Supressors |
| LCE8.5A | Silicon Avalanche Diodes - 1500W Axial Leaded Transient Voltage Supressors |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1962M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Fan Motor Single-Phase Full-Wave Drivers |
| LB1962MC-AH | 功能描述:馬達/運動/點火控制器和驅動器 BRUSHLESS MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1964 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Fan Motor Single-Phase Full-Wave Driver |
| LB1964T | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Fan Motor Single-Phase Full-Wave Driver |
| LB1965 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Two-Phase Unipolar Driver for Variable-Speed Fan Motor |
發布緊急采購，3分鐘左右您將得到回復。