- 您現在的位置：買賣IC網 > PDF目錄358747 > LB1863M (Sanyo Electric Co.,Ltd.) Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package PDF資料下載
參數資料
| 型號： | LB1863M |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| 中文描述： | 兩相單極無刷電機驅動器自動恢復型電路的微型扁平封裝 |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 76K |
| 代理商： | LB1863M |
No. 4943-5/5
LB1863M, 1869M
4. Output protection function (C pin)
This pin connects the capacitor that forms the automatic recovery circuit. If rotation stops due to, for example, a
motor overload, the pin voltage rises and the output stops. The system automatically recovers from stopped to drive
mode when the load is set to an appropriate level. The lock detection time can be set by changing the value of the
capacitor.
For a 1-μF capacitor:Lock detection time
Lock protection time (output on)
(output off) About 6 seconds
About 2 seconds
About 1 second
This catalog provides information as of January, 1997. Specifications and information herein are subject to
change without notice.
I
No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
I
Anyone purchasing any products described or contained herein for an above-mentioned use shall:
Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
I
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
While the blades are turning, the capacitor is charged with a current of about 3 μA (typical), and C is discharged by
pulses that correspond to the motor speed.
When the blades lock, the capacitor is no longer discharged, and the voltage across the capacitor increases. The
output is turned off when that voltage reaches 0.8
×
V
IN
.
When the output is turned off, the capacitor is discharged at a current of about 0.44 μA (typical). When the
capacitor voltage falls under V
TH
2, if the lock state is not yet cleared the capacitor continues discharging until
V
TH
1. (Note that the output is turned on at this time.) These operations, i.e. items
and
, are repeated with a
ton:toff ratio of about 1:6 to protect the motor.
{
If the lock state has been cleared when the capacitor voltage reaches V
TH
2, motor rotation is started by turning the
output on.
5. Rotation detection signal (RD pin)
This is an open collector output, and outputs a low level in drive mode and a high level when the motor is stopped.
6. Radio-frequency noise reduction function (B1 and B2 pins)
These are base pins for Darlington pair outputs. Add capacitors of about 0.01 to 0.1 μF if radio-frequency noise is a
problem.
7. Thermal shutdown function
Turns off the output in response to coil shorting or IC overheating.
Automatic recovery circuit pin C voltage
相關PDF資料 |
PDF描述 |
|---|---|
| LB1868M | RES 10.0MEGOHM MTL FLM.40W 1% TR |
| LB1868 | Two-Phase Brushless Fan Motor Driver |
| LB1870 | Three-Phase Brushless Motor Driver(3相位無電刷馬達驅動器) |
| LB1871 | Three-Phase Brushless Motor Driver |
| LB1871M | Three-Phase Brushless Motor Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB1863M_09 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Two-Phase Unipolar Brushless Motor Driver Automatic Recovery Type Circuit in a Miniature Flat Package |
| LB1863M-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1863M-MPB-H | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1863M-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB1863M-TLM-H | 功能描述:馬達/運動/點火控制器和驅動器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。