- 您現在的位置：買賣IC網 > PDF目錄97997 > LB11948T STEPPER MOTOR CONTROLLER, 0.5 A, PDSO30 PDF資料下載
參數資料
| 型號： | LB11948T |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.5 A, PDSO30 |
| 封裝： | 0.275 INCH, TSSOP-30 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 161K |
| 代理商： | LB11948T |
LB11948T
No.7947-4/13
Pin Functions
Pin No.
Pin Name
Description
1
OUT1-
Output
2
OUT1
Output
3
NC
Unused
4
NC
Unused
5
D-GND
Lower side internal diode anode connection
6
E1
Constant current control sensing
The motor current is set by the value of the sensing resistor Re connected between the E1 pin and ground.
The current is set according to the following equation : IO = VREF/Re (A)
7
VS1
VS power supply
8
NC
Unused
9
VCC
VCC power supply
10
CR
RC oscillator connection
11
VREF1
Current setting system reference voltage input
VREF1 voltage range : 0 to 0.5V
12
NC
Unused
13
ENABLE1
Output is turned on when ENABLE1 is low, and the output is turned off (operating state) when ENABLE1 is high.
14
PHASE1
Logic level input : phase switching
When PHASE1 = high : Output pin states : OUT1 : high, OUT1- : low.
When PHASE1 = low : Output pin states : OUT1 : low, OUT1- : high.
15
ST
Standby mode setting
When ST = high : the IC operates in normal operating mode.
When ST = low : the IC operates in standby mode. The VS and VCC current drain levels are under 1μA in this mode.
16
NC
Unused
17
1VREG
1V regulator circuit output
The LB11948 includes an internal 1V regulator circuit, and this pin is the output from that circuit. The VREF1 and VREF2
reference voltages can be set by voltage dividing the 1V regulator output.
18
PHASE2
Logic level input : phase switching
When PHASE2 = high : Output pin states : OUT2 : high, OUT2- : low.
When PHASE2 = low : Output pin states : OUT2 : low, OUT2- : high.
19
ENABLE2
Output is turned on when ENABLE2 is low, and the output is turned off (operating state) when ENABLE2 is high.
20
VREF2
Current setting reference voltage input
VREF2 voltage range : 0 to 0.5V
21
GND
Ground (small signal circuit system ground)
22
PGND
Power system ground (high current circuit system ground)
23
NC
Unused
24
VS2
VS power supply
25
E2
Constant current control sensing
The motor current is set by the value of the sensing resistor Re connected between the E2 pin and ground.
The current is set according to the following equation : IO = VREF/Re (A)
26
D-GND2
Lower side internal diode anode connection
27
NC
Unused
28
NC
Unused
29
OUT2
Output
30
OUT2-
Output
相關PDF資料 |
PDF描述 |
|---|---|
| LB1814M | DISK DRIVE MOTOR CONTROLLER, 1 A, PDSO36 |
| LB1821M | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PQFP44 |
| LB1823M | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO30 |
| LB1875 | BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36 |
| LB1897H | BRUSHLESS DC MOTOR CONTROLLER, PDSO34 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LB11948T_07 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11948T_10 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:PWM Constant Current Control 1-2 Phase Excitation Stepping Motor Driver |
| LB11948T-MPB-E | 功能描述:馬達/運動/點火控制器和驅動器 RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB11948T-TLM-E | 功能描述:馬達/運動/點火控制器和驅動器 PRINTER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| LB-1195 | 制造商:Ideal Industries Inc 功能描述:WIRESTOP STMLT STD 制造商:Ideal Industries Inc 功能描述:Stripmaster Lite Repair |
發布緊急采購，3分鐘左右您將得到回復。