- 您現在的位置：買賣IC網 > PDF目錄383236 > L6280 (意法半導體) THREE CHANNELS MULTIPOWER DRIVER SYSTEM PDF資料下載
參數資料
| 型號： | L6280 |
| 廠商： | 意法半導體 |
| 英文描述： | THREE CHANNELS MULTIPOWER DRIVER SYSTEM |
| 中文描述： | 三通道移動電站驅動系統 |
| 文件頁數： | 18/26頁 |
| 文件大小： | 388K |
| 代理商： | L6280 |
APPLICATION INFORMATION
An application circuit useful to test the perform-
ance of the L6280 can be formed as shown on
Figure 24: CH1 drives one unipolar stepper mo-
tor, CH2 drives a DC motor, CH3 drives one sole-
noid and the SMPS can supplycontinuously0.5A.
If the Watch Dog and the Chip Select functions
are not of interest, pins 22 and 23 must be
grounded. Each sensing resistor would be ob-
tained by the parallelof two or more metal filmre-
sistor of the same value to minimize their series
equivalentinductance.
Generally, optimum stability of the SMPS voltage
control loop, is achieved by a series network
made by 1nF and 39 K
(see pin 15) and by us-
ing an output capacitor of 10
0μ
F having an
equivalent series resistance of 100 m
(see pin
14): the mostof the unexpensivealuminium elec-
trolithic capacitorscan be right.
The snubber network at the secondary winding of
the step-down inductor can be saved by accept-
ing a not regulated voltage at the Charge Pump
input pin 13. This condition is not recommended
when the supply voltage and/or the SMPS output
current changes too much (for instance respec-
tively20V + 30% and/or 100 to 800 mA).
The inductance value of the primarywinding of T1
defines the peak-to peak current ripple that flows
throught itself, that is the minimum output current
that allows the correct behaviour in continuous
mode of the SMPS; nevertheless, the device is
not demaged if it is obliged to work in discontinu-
ous mode at a low current level.
Figure 25 shows the characteristics of the trans-
former T1 suitable to be used on the Application
of Figure 24:
The maximum output current is of 500 mA con-
tinuous but current peaks of 800 mA can be
sinked out without the risk of the core saturation.
To avoid the discontinuous mode, the minimum
SMPS output current must be of 70mA. The recti-
fied voltage trend for the high side gate drive at
pin 13 is as shown on Figure26.
Not equally cheap, the choice of a toroidal core
for T1 can optimize theapplication.
Instead of this, another solution can be as in Fig-
ure 27a it is shown. This is a full wave rectifier of
the voltageat pin 3; Z1 and R1 clamp the positive
peak while the forward characteristicof the Zener
rectifies the negative peak and charges C1. The
recommendedZener voltageis of 12V.
Could happen that the V
SS
output voltage is not
requestedbecause already available: in this case
and only if at least one unipolar stepper motor is
continuously driven, the solution shown in Figure
27b can be implemented. The step down output
componentscan be leftout.
The connectionof the network is asfollows:
A: to pin 4 (or pin 5) when the unipolar motor is
driven via CH1;
to pin 41 (or pin 42) when the unipolar motor
is driven via CH2;
B: to pin 1
C: to pin13
The SMPS switching frequencyis the sameof the
oscillator frequency that can be typically defined
by:
f
osc
=
9
RC
Referringto Fig.24 it is calculated f
osc
= 82KHz.
CH3 is chopped at the same frequency. The out-
put diodes must be chosen according to the sole-
noid working current (50ns of reverse recovery
time or better): for a current less than 1 A, the
PLQ08is a good choice.
Driving one unipolarsteppermotor, output protec-
tion diodes (Transil) are recommended: CH1 in
Fig 24 uses four BZW04 - 48 diodes; when a low
current motor is driven or a Vs less than 20V is
supplied, four fast diodes and only one Zener di-
ode can be used as a protection of the outpus
(see Figure 28). The driving of DC motor needs
the connectionas shown for CH2 (full bridge con-
figuration).
The drive of one bipolar stepper motor by using
CH1 and CH2 both in full bridge configuration al-
lows the use of a higher supply voltage level that
however cannot exceed the Absolute Maximum
Figure23
D0
D1
D2
D3
X
1
1
1
Tristate left and right (see
X000 configuration of full
bridge).
L6280
18/26
相關PDF資料 |
PDF描述 |
|---|---|
| L6285 | 3 CHANNELS MULTIPOWER SYSTEM |
| L6285S | 3 CHANNELS MULTIPOWER SYSTEM |
| L6316 | 4-CHANNEL LOW POWER PREAMPLIFIER |
| L634 | THREE PHASE MOTOR DRIVER |
| L6353 | Smart Driver for Power MOS & IGBT(用于MOS和絕緣柵雙極晶體管的智能驅動器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6281B12D | 制造商:ST MICRO 功能描述:New |
| L6282-3.2E | 制造商:STMicroelectronics 功能描述:L6282-3.2E |
| L6283-1.2 | 制造商:STMicroelectronics 功能描述:ELECTRONIC COMPONENT |
| L6283-1.3 | 制造商:STMicroelectronics 功能描述:ELECTRONIC COMPONENT |
| L6285 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 CHANNELS MULTIPOWER SYSTEM |
發布緊急采購，3分鐘左右您將得到回復。