hbwhelp@micrel.com or (408) 955-1690 2.10.2 I
參數資料
型號： KSZ8993F
廠商： Micrel Inc
文件頁數： 39/100頁
文件大?。?/td> 0K
描述： IC CONV MED 10/100 3PORT 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 散裝
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1033
Micrel, Inc.
KS8993F/FL
June 2009
43
M9999-062509
hbwhelp@micrel.com or (408) 955-1690
2.10.2 I
2C Slave Serial Bus Configuration
In managed mode, the KS8993F can be configured as an I
2C slave device. In this mode, an I2C master device
(external controller/CPU) has complete programming access to the KS8993F’s 128 registers. Programming access
includes the Global Registers, Port Registers, Media Converter Registers, Advanced Control Registers and indirect
access to the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters
are indirectly accessed via registers 110 thru 120.
In I
2C slave mode, the KS8993F operates like other I2C slave devices. Addressing the KS8993F’s 8 bit registers is
similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of I
2C read/write operations and related
timing information can be found in the AT24C02 Datasheet.
Two fixed 8 bit device addresses are used to address the KS8993F in I
2C slave mode. One is for read; the other is for
write. The addresses are as follow:
1011_1111
<read>
1011_1110
<write>
The following is a sample procedure for programming the KS8993F using the I
2C slave serial bus:
1.
Enable I
2C slave mode by setting the KS8993F strap-in pins PS[1:0] (pins 100 and 101 respectively) to “01”.
2.
Power up the board and assert reset to the KS8993F. After reset, the “Start Switch” bit (register 1 bit 0) will be
set to ‘0’.
3.
Configure the desired register settings in the KS8993F, using the I
2C write operation.
4.
Read back and verify the register settings in the KS8993F, using the I
2C read operation.
5.
Write a ‘1’ to the “Start Switch” bit to start the KS8993F with the programmed settings.
Note: The “Start Switch” bit cannot be set to ‘0’ to stop the switch after an ‘1’ is written to this bit. Thus, it is
recommended that all switch configuration settings are programmed before the “Start Switch” bit is set to ‘1’.
Some of the configuration settings, such as “Aging enable”, “Auto Negotiation Enable”, “Force Speed” and
“Power down” can be programmed after the switch has been started.
2.10.3 SPI Slave Serial Bus Configuration
In managed mode, the KS8993F can be configured as a SPI slave device. In this mode, a SPI master device (external
controller/CPU) has complete programming access to the KS8993F’s 128 registers. Programming access includes the
Global Registers, Port Registers, Media Converter Registers, Advanced Control Registers and indirect access to the
“Static MAC Table”, “VLAN Table”, “Dynamic MAC Table” and “MIB Counters”. The tables and counters are indirectly
accessed via registers 110 thru 120.
The KS8993F supports two standard SPI commands: ‘0000_0011’ for data read and ‘0000_0010’ for data write. SPI
multiple read and multiple write are also supported by the KS8993F to expedite register read back and register
configuration, respectively.
SPI multiple read is initiated when the master device continues to drive the KS8993F SPIS_N input pin (SPI Slave
Select signal) low after a byte (a register) is read. The KS8993F internal address counter will increment automatically
to the next byte (next register) after the read. The next byte at the next register address will be shifted out onto the
KS8993F SPIQ output pin. SPI multiple read will continue until the SPI master device terminates it by de-asserting the
SPIS_N signal to the KS8993F.
相關PDF資料
PDF描述
LFXP3C-4QN208I IC FPGA 3.1KLUTS 136I/O 208-PQFP
RF803E-SO IC ENCODER 3 DGTL I/O SOT23-6
AMM22DRYH-S13 CONN EDGECARD 44POS .156 EXTEND
LFXP6E-3T144C IC FPGA 5.8KLUTS 100I/O 144-TQFP
LFXP6E-3TN144C IC FPGA 5.8KLUTS 144TQFP
相關代理商/技術參數
參數描述
KSZ8993F-A1 功能描述:IC CONV MED 10/100 3PORT 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993F-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993F RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993FL 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Transceivers & TS-1000 OAM, single 3.3V supply, 128-PQFP, Lead free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993FL-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993FL RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993I 功能描述:以太網 IC 3 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-PQFP, I-TEMP RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*