- 您現在的位置：買賣IC網 > PDF目錄299287 > KQM0603TTER15G (KOA SPEER ELECTRONICS INC) 1 ELEMENT, 0.15 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD PDF資料下載
參數資料
| 型號： | KQM0603TTER15G |
| 廠商： | KOA SPEER ELECTRONICS INC |
| 元件分類： | 通用定值電感 |
| 英文描述： | 1 ELEMENT, 0.15 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| 封裝： | CHIP, 0603 |
| 文件頁數： | 5/9頁 |
| 文件大?。?/td> | 426K |
| 代理商： | KQM0603TTER15G |
5^ 9j
9. RELIABILITY TESTS
9-1 Electrical Characteristics
ITEM
REQUIREMENT
TEST METHODS
Dielectric
Withstanding
Voltage
No evidence of
flaming, fuming,
or breakdown
5 seconds at AC 500V applied
between both terminals and film.
Insulation
Resistance
1000M
and over
1 minute at DC 100V measured
between both terminals and film.
Flammability
IEC 695-2-2
Withstands needle-flame test.
9-2 Mechanical Characteristics
ITEM
REQUIREMENT
TEST METHODS
Terminal
Pull Strength
No evidence of
damage
Terminals shall be withstand a pull
of
5N in a horizontal direction.
Terminal Bending
Strength
No evidence of
breakdown
Specimen shall be soldered on bend
test board and force applied to the
opposite side to cause a 3 mm
deflection
Vibration
L/L within } 5%
Q/Q within } 10%
2 hours in each direction of X,Y,Z
on PCB at a frequency range of
10-55-10Hz with 1.5 mm amplitude
Dropping
No evidence of
damage
L/L within } 5%
Q/Q within } 10%
Dropping 1 m on the ground of
concrete 1 time
Resistance to
Soldering Heat
No evidence of
outer damage
L/L within } 5%
Q/Q within } 10%
Immerse in the solder at 260} 5
for 10} 1 seconds
Solderability
95% of the
terminal should be
covered with new solder
Immerse in the solder at 230} 5
for 3} 0.5 seconds
Resistance to
Solvent
No damage and
marking must
remain legible
Accordance with MIL-STD-202F
Method 215
KOA CORPORATION
相關PDF資料 |
PDF描述 |
|---|---|
| KQM0603TTER12K | 1 ELEMENT, 0.12 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| KQM0603TTER11K | 1 ELEMENT, 0.11 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| KQM0603TTER11J | 1 ELEMENT, 0.11 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| KQM0603TTER10J | 1 ELEMENT, 0.1 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
| KQM0603TTE9N5D | 1 ELEMENT, 0.0095 uH, CERAMIC-CORE, GENERAL PURPOSE INDUCTOR, SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KQN04-99 | 制造商:SMC 功能描述:Pneumatic push-in nipple connector,4mm |
| KQN06-99 | 制造商:SMC 功能描述:Pneumatic push-in nipple connector,6mm |
| KQN08-99 | 制造商:SMC 功能描述:Pneumatic push-in nipple connector,8mm |
| KQN10-99 | 制造商:SMC 功能描述:Pneumatic push-in nipple connector,10mm |
| KQN12-99 | 制造商:SMC 功能描述:Pneumatic push-in nipple connector,12mm |
發布緊急采購，3分鐘左右您將得到回復。