參數資料
型號： KITMPR084EVM
廠商： Freescale Semiconductor
文件頁數： 9/40頁
文件大?。?/td> 0K
描述： KIT EVAL 8-PAD TOUCH MPR084
標準包裝： 1
傳感器類型： 觸摸，電容式
接口： I²C
電源電壓： 1.8 V ~ 3.6 V
嵌入式： 是，其它
已供物品： 板，纜線，CD
已用 IC / 零件： MPR084
產品目錄頁面： 2808 (CN2011-ZH PDF)
相關產品： MPR084EJR2CT-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084QR2-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR084Q-ND - IC CTLR TOUCH SENSOR PROX 16-QFN
MPR084EJR2TR-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084EJ-ND - IC CTLR TOUCH SENSR PROX 16TSSOP
MPR084
Sensors
Freescale Semiconductor
17
5
Low Power Configuration
5.1
Introduction
The MPR084 features a Low Power mode that can reduce the power consumption into the microamps range. This feature can
be used to both adjust the response time of the system, and change the conditions on which Low Power would be enabled.
5.2
Operation
This Low Power configuration is only active when the sensor controller is in Run2 mode. The Low Power mode decreases current
consumption by increasing the response time of the MPR084. This increase is controlled through two factors.
During normal Run2 operation of the sensor controller the Max Response Time (MRT) is calculated by taking the product of the
TASP and the primary clock. From Chapter 4 the primary clock is the (MTP + 5) ms. Since the sensor controller is in Run2, the
primary clock is also multiplied by a factor of 8. The debounce rate of the MPR084 is 4 times the sample rate thus the MRT is
represented by the following equation.
Equation 1
First, the Idle Interface Timeout (IIT) represents the total time the touch interface should remain idle before going into Low Power
mode. This value can be calculated by taking the product of the ITP, TASP and primary clock (8ms) with a factor of 64. Thus the
IIT is represented as follows:
Equation 2
Second, the Max Response Time (MRT) represents the total time the touch interface should remain inactive before scanning the
electrodes. This value can be calculated by taking the product of the SCD, TASP and primary clock (8ms) with a factor of 5. Thus
the MRT is represented as follows:
Equation 3
When in Run2 mode, the sensor controller will initially scan the electrodes at the rate of MRT1. When scanning at MRT1 and the
touch interface remains idle for the IIT period then the scan period will change to MRT2. When scanning at MRT2 and a touch is
detected the scan rate will transition back to MRT1.
Figure 20. Low Power Scan Period Transition Diagram
5.3
Configuration
Low Power Configuration is achieved through setting two values; the Idle Timeout Period and the Sleep Cycle Duration. This
functionality is described in the following section.
MRT1
MTP
5
+
8
----------------------
1
+
TASP
48ms
=
MRT2
MTP
5
+
8
----------------------
1
+
TASP
SCD
48
ms
=
ITT
MTP
5
+
8
----------------------
1
+
TASP
ITP
68ms
=
LP DISABLED
ITT PERIOD
run2 SET
TOUCH DETECTED
MRT1
MRT2
相關PDF資料
PDF描述
MIC4467ZN IC DRIVER MOSF QUAD 1.2A 14-DIP
MIC4467ZWM IC DRIVER MOSF QUAD 1.2A 16-SOIC
MIC4468ZWM IC DRIVER MOSF QUAD 1.2A 16SOIC
ECM11DSEF CONN EDGECARD 22POS .156 EYELET
C8051F560DK KIT DEVELOPMENT FOR C8051F560
相關代理商/技術參數
參數描述
KITMPR121EVM 功能描述:觸摸傳感器開發工具 MPR121 Sensor Tool Box RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度:
KITMPR121EVM 制造商:Freescale Semiconductor 功能描述:Sensor Toolbox Proximity Sensor Kit
KITMPVZ5004EVK 功能描述:壓力傳感器開發工具 WATER LEVEL BOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXA6115AEVB 功能描述:壓力傳感器開發工具 Sensor Toolbx Pressu Sensor Developmt brd RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
KITMPXSHOWEVK 功能描述:壓力傳感器開發工具 PRESSURE SHOWBOARD RoHS:否 制造商:Freescale Semiconductor 工具用于評估:MPL3115A2 接口類型:USB 最大工作溫度:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*