- 您現在的位置：買賣IC網 > PDF目錄16433 > KIT33972AEWEVBE (Freescale Semiconductor)KIT EVALUATION FOR MC33972 PDF資料下載
參數資料
| 型號： | KIT33972AEWEVBE |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVALUATION FOR MC33972 |
| 標準包裝： | 1 |
| 主要目的： | 接口，開關探測 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | MC33972 |
| 主要屬性： | 8 可編程輸入（電池開關或接地開關） |
| 次要屬性： | 14 開關至接地輸入 |
| 已供物品： | 板，CD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
19
33972
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
EXAMPLE OF NORMAL MODE OPERATION
The operation of the device in Normal mode is defined by
the states of the programmable internal control registers. A
typical application may have the following settings:
Programmable switch – set to switch-to-ground
All inputs set as wake-up
Wetting current on (16 mA)
Wetting current timer on (20 ms)
All inputs tri-state-disabled (comparator is active)
Analog select 00000 (no input channel selected)
With the device programmed as above, an interrupt will be
generated with each switch contact change of state (open-to-
close or close-to-open) and 16 mA of contact wetting current
will be source for 20 ms. The INT pin will remain LOW until
switch status is acknowledged by the microprocessor. It is
critical to understand INT will not be cleared on the rising
edge of CS if a switch closure occurs while CS is LOW. The
maximum duration a switch state change can exist without
acknowledgement depends on the software response time to
the interrupt. Figure 6, page 9, shows the interaction
between changing input states and the INT and CS pins.
If desired the user may disable interrupts (wake up/
interrupt command) from the 33972 device and read the
switch states on a periodic basis. Switch activation and
deactivation faster than the MCU read rate will not be
acknowledged.
The 33972 device will exit the Normal mode and enter the
Sleep mode only with a valid sleep command.
SLEEP MODE
Sleep mode is used to reduce system quiescent currents.
Sleep mode may be entered only by sending the sleep
command. All register settings programmed in Normal mode
will be maintained in Sleep mode.
The 33972 will exit Sleep mode and enter Normal mode
when any of the following events occur:
Input switch change of state (when enabled)
Interrupt timer expire
Falling edge of WAKE
Falling edge of INT (with VDD = 5.0 V and WAKE at
Logic [1])
Falling edge of CS (with VDD = 5.0 V)
Power-ON Reset (POR)
The VDD supply may be removed from the device during
Sleep mode. However removing VDD from the device in Sleep
mode will disable a wake-up from falling edge of INT and CS.
Note In cases where CS is used to wake the device, the
first SO data message is not valid.
The sleep command contains settings for two
programmable timers for Sleep mode, the interrupt timer and
the scan timer, as shown in Table 18 The interrupt timer is
used as a periodic wake-up timer. When the timer expires, an
interrupt is generated and the device enters Normal mode.
Note The interrupt timer in the 33972 device may be
disabled by programming the interrupt bits to logic [1 1 1].
Table 19 shows the programmable settings of the Interrupt
timer.
Table 16. Serial Output (SO) Bit Data
Type of Input
Input
Programmed
Voltage on
Input Pin
SO SPI Bit
SP
Switch to Ground
SPn < 4.0V
1
Switch to Ground
SPn > 4.0V
0
Switch to Battery
SPn < 4.0V
0
Switch to Battery
SPn > 4.0V
1
SG
N/A
SGn < 4.0V
1
N/A
SGn > 4.0V
0
Table 17. Serial Output (SO) Response Register
SO Response Will
Always Send
them
flg
int
flg
SP7
SP6
SP5
SP4
SP3
SP2
SP1
SP0 SG13 SG12 SG11 SG10 SG9 SG8 SG7 SG6 SG5 SG4 SG3 SG2 SG1 SG0
Table 18. Sleep Command
Sleep Command
Command Bits
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
1
0
X
int
timer
int
timer
int
timer
scan
timer
scan
timer
scan
timer
相關PDF資料 |
PDF描述 |
|---|---|
| EBM31DCMS | CONN EDGECARD 62POS .156 WW |
| VI-J1L-EX | CONVERTER MOD DC/DC 28V 75W |
| XR16V598IQ-0B-EVB | EVAL BOARD FOR XR16V598-A 100QFP |
| CM322522-820KL | INDUCTOR 82UH 60MA SMD |
| VI-2V2-EX | CONVERTER MOD DC/DC 15V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KIT33975AEWEVBE | 功能描述:交換機 IC 開發工具 MULTIPLE SWITCH DETECT I RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| KIT33982CEVBE | 功能描述:電源管理IC開發工具 2.0 M HIGH-SIDE SW RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| KIT33982PNAEVB | 功能描述:電源管理IC開發工具 SPSS HIGH-SIDE SWTCH RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| KIT33984CEVBE | 功能描述:電源管理IC開發工具 4.0 M HIGH-SIDE SW RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| KIT33984PNAEVB | 功能描述:電源管理IC開發工具 33984 - SPD4 EVAL KIT RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。