- 您現在的位置：買賣IC網 > PDF目錄384536 > ISPGDX80VA-5T100I (LATTICE SEMICONDUCTOR CORP) In-System Programmable 3.3V Generic Digital CrosspointTM PDF資料下載
參數資料
| 型號： | ISPGDX80VA-5T100I |
| 廠商： | LATTICE SEMICONDUCTOR CORP |
| 元件分類： | PLD |
| 英文描述： | In-System Programmable 3.3V Generic Digital CrosspointTM |
| 中文描述： | EE PLD, 5 ns, PQFP100 |
| 封裝： | TQFP-100 |
| 文件頁數： | 20/27頁 |
| 文件大?。?/td> | 346K |
| 代理商： | ISPGDX80VA-5T100I |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
20
Specifications
ispGDX80VA
Figure 9. ispJTAG Device Programming Interface
In-System Programmability
All necessary programming of the ispGDXVA is done via
four TTL level logic interface signals. These four signals
are fed into the on-chip programming circuitry where a
state machine controls the programming.
On-chip programming can be accomplished using an
IEEE 1149.1 boundary scan protocol. The IEEE 1149.1-
compliant interface signals are Test Data In (TDI), Test
Data Out (TDO), Test Clock (TCK) and Test Mode Select
(TMS) control. The EPEN pin is also used to enable or
disable the JTAG port.
The embedded controller port enable pin (EPEN) is used
to enable the JTAG tap controller and in that regard has
similar functionality to a TRST pin. When the pin is driven
high, the JTAG TAP controller is enabled. This is also true
when the pin is left unconnected, in which case the pin is
pulled high by the permanent internal pullup. This allows
ISP programming and BSCAN testing to take place as
specified by the Instruction Table.
When the pin is driven low, the JTAG TAP controller is
driven to a reset state asynchronously. It stays there
while the pin is held low. After pulling the pin high the
JTAG controller becomes active. The intent of this fea-
ture is to allow the JTAG interface to be directly controlled
by the data bus of an embedded controller (hence the
name Embedded Port Enable). The EPEN signal is used
as a
“
device select
”
to prevent spurious programming
and/or testing from occuring due to random bit patterns
on the data bus. Figure 9 illustrates the block diagram for
the ispJTAG interface.
ispGDX
80VA
Device
TDO
TDI
TMS
TCK
EPEN
ispJTAG
Programming
Interface
ispLSI
Device
ispMACH
Device
ispGDX
80VA
Device
ispGDX
80VA
Device
相關PDF資料 |
PDF描述 |
|---|---|
| ISPGDX80VA-7T100I | PHOTOELECTRIC PRODUCTS |
| ISPGDX80VA-9T100I | In-System Programmable 3.3V Generic Digital CrosspointTM |
| ISPL1048E-125LQI | High-Density Programmable Logic |
| ISPL1048E-100LQ | High-Density Programmable Logic |
| ISPL1048E-100LQI | High-Density Programmable Logic |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISPGDX80VA-5TN100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-5TN100I | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-7T100 | 功能描述:模擬和數字交叉點 IC 3.3V 80 I/O RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-7T100I | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| ISPGDX80VA-7TN100 | 功能描述:模擬和數字交叉點 IC PROGRAMMABLE GEN DIG CROSSPOINT RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。