參數資料
型號： ISP1107
廠商： NXP Semiconductors N.V.
英文描述： Advanced Universal Serial Bus transceiver
中文描述： 先進的通用串行總線收發器
文件頁數： 4/19頁
文件大?。?/td> 536K
代理商： ISP1107
Philips Semiconductors
ISP1107
Advanced USB transceiver
Objective specification
Rev. 01 — 23 February 2000
4 of 19
9397 750 06899
Philips Electronics N.V. 2000. All rights reserved.
7.
Functional description
7.1 Function selection
[1]
[2]
Signal levels on D
+
/D
are determined by other USB devices and external pull-up/down resistors.
In ‘suspend’ mode (SUSPND = HIGH) the differential receiver is inactive and output RCV is always
LOW. Out-of-suspend (‘K’) signalling is detected via the single-ended receivers VP and VM.
During suspend, the slew-rate control circuit of low-speed operation is disabled. The D
+
/D
are still
driven to their intended states, without slew-rate control. This is permitted because driving during
suspend is used to signal remote wakeup by driving a ‘K’ signal (one transition from idle to ‘K’ state)
for a period of 1 to 15 ms.
[3]
GND
V
CC(I/O)
8
9
-
-
ground supply
supply voltage for digital I/O pins (1.65 to 3.6 V). Three
voltage levels are supported: 1.8 V
±
0.15 V, 2.5 V
±
0.2 V
and 3.3 V
±
0.3V; when V
CC(I/O)
is not connected, the D+/D
pins are in three-state
speed selection input (CMOS level re. V
CC(I/O)
); adjusts the
slew rate of differential data outputs D
+
and D
according to
the transmission speed:
SPEED
10
I
LOW:
low-speed (1.5 Mbit/s)
HIGH:
full-speed (12 Mbit/s)
negative USB data bus connection (analog, differential); for
low-speed mode connect to pin V
pu(3.3)
via a 1.5 k
resistor
positive USB data bus connection (analog, differential); for
full-speed mode connect to pin V
pu(3.3)
via a 1.5 k
resistor
differential driver data input (CMOS level re. V
CC(I/O)
, Schmitt
trigger); see
Table 4
differential driver data input (CMOS level re. V
CC(I/O)
, Schmitt
trigger); see
Table 4
regulated supply voltage output (3.0 to 3.6 V) during 5 V
operation; used as supply voltage input for 3.3 V operation
(3.3 V
±
10%)
supply voltage for 5 V operation (4.0 to 5.5 V); can be
connected directly to USB supply V
BUS
; connect this pin to
V
reg(3.3)
during 3.3 V operation
D
11
AI/O
D
+
12
AI/O
VO
13
I
FSE0
14
I
V
reg(3.3)
15
-
V
CC(5.0)
16
-
Table 2:
Symbol
Pin description
…continued
Pin
Type
Description
Table 3:
SUSPND
L
Function table
OE
L
D
+
/D
driving &
receiving
receiving
[1]
driving
RCV
active
VP/VM
active
Function
normal driving
(differential receiver active)
receiving
driving during ‘suspend’
[3]
(differential receiver inactive)
low-power state
L
H
H
L
active
inactive
[2]
active
active
H
H
high-Z
[1]
inactive
[2]
active
相關PDF資料
PDF描述
ISP1107DH Advanced Universal Serial Bus transceivers
ISP1107W Advanced Universal Serial Bus transceivers
ISP1109 Universal Serial Bus transceiver with carkit support
ISP1109BS Universal Serial Bus transceiver with carkit support
ISP1122A Universal Serial Bus stand-alone hub
相關代理商/技術參數
參數描述
ISP1107DH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceiver
ISP1107W 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced Universal Serial Bus transceivers
ISP1109 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver with carkit support
ISP1109BS 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus transceiver with carkit support
ISP1109BS,118 功能描述:射頻收發器 USB FS TRANSCVR RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*