- 您現在的位置：買賣IC網 > PDF目錄384533 > ISL97536IUZ-TK (INTERSIL CORP) Monolithic 1A Step-Down Regulator with Low Quiescent Current PDF資料下載
參數資料
| 型號： | ISL97536IUZ-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Monolithic 1A Step-Down Regulator with Low Quiescent Current |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | ROHS COMPLIANT, MSOP-10 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 265K |
| 代理商： | ISL97536IUZ-TK |
8
FN6279.0
October 5, 2006
Component Selection
Because of the fixed internal compensation, the component
choice is relatively narrow. For a regulator with fixed output
voltage, only two capacitors and one inductor are required.
Capacitors must be chosen in the range of 10μF to 40μF,
multilayer ceramic capacitors with X5R or X7R rating for
both the input and output capacitors, and inductors in the
range of 1.5μH to 2.2μH.
The RMS current present at the input capacitor is decided by
the following formula:
This is about half of the output current I
O
for all the V
O
. This
input capacitor must be able to handle this current.
The inductor peak-to-peak ripple current is given as:
L is the inductance
f
S
the switching frequency (nominally 1.4MHz)
The inductor must be able to handle I
O
for the RMS load
current, and to assure that the inductor is reliable, it must
handle the 2A surge current that can occur during a current
limit condition.
In addition to decoupling capacitors and inductor value, it is
important to properly size the phase-lead capacitor C
4
(Refer to the Typical Application Diagram). The phase-lead
capacitor creates additional phase margin in the control loop
by generating a zero and a pole in the transfer function. As a
general rule of thumb, C
4
should be sized to start the phase-
lead at a frequency of ~2.5kHz. The zero will always appear
at lower frequency than the pole and follow the equation
below:
Over a normal range of R
2
(~10-100k), C
4
will range from
~470-4700pF. The pole frequency cannot be set once the
zero frequency is chosen as it is dictated by the ratio of R
1
and R
2
, which is solely determined by the desired output set
point. The equation below shows the pole frequency
relationship:
Layout Considerations
The layout is very important for the converter to function
properly. The following PC layout guidelines should be
followed:
1. Separate the Power Ground (
(
); connect them only at one point right at the pins
2. Place the input capacitor as close to V
IN
and PGND pins
as possible
3. Make the following PC traces as small as possible:
- from LX pin to L
- from C
O
to PGND
4. If used, connect the trace from the FB pin to R
1
and R
2
as close as possible
5. Maximize the copper area around the PGND pin
6. Place several via holes under the chip to additional
ground plane to improve heat dissipation
The demo board is a good example of layout based on this
outline. Please refer to the ISL97536 Application Brief.
) and Signal Ground
I
INRMS
V
V
V
IN
)
-------------------------------–
I
O
×
=
(EQ. 3)
I
IL
V
(
-------------------------------------------
V
)
IN
V
O
S
×
–
=
(EQ. 4)
f
Z
2
π
R
2
C
4
----------------------
=
(EQ. 5)
f
P
2
π
R
1
R
2
(
)
C
4
---------------------------------------
=
(EQ. 6)
ISL97536
相關PDF資料 |
PDF描述 |
|---|---|
| ISL97631 | White LED Boost Regulator With Integrated Schottky Diode |
| ISL97631IHTZ-T7 | White LED Boost Regulator With Integrated Schottky Diode |
| ISL97631IHTZ-T7A | White LED Boost Regulator With Integrated Schottky Diode |
| ISL97632_07 | White LED Driver with Digital Dimming |
| ISL97632IRT14Z-T | White LED Driver with Digital Dimming |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL97631HTZ-T7A | 制造商:Intersil Corporation 功能描述: |
| ISL97631IHTZ | 制造商:Intersil 功能描述:6 LEDs Driver with Integrated Schottky Diode with OVP |
| ISL97631IHTZ-T7 | 功能描述:IC LED DRIVR WHITE BCKLGT TSOT-6 RoHS:是 類別:集成電路 (IC) >> PMIC - LED 驅動器 系列:- 標準包裝:60 系列:- 恒定電流:- 恒定電壓:- 拓撲:線性（LDO），PWM，升壓（升壓） 輸出數:8 內部驅動器:是 類型 - 主要:背光 類型 - 次要:RGB，白色 LED 頻率:500kHz ~ 1.5MHz 電源電壓:4.75 V ~ 26 V 輸出電壓:45V 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* 工作溫度:-40°C ~ 85°C |
| ISL97631IHTZ-T7A | 功能描述:LED顯示驅動器 ISL97631IHTZ HI PWR WHT LED BOOSTLT1933 RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| ISL97632IRT14Z | 制造商:Intersil 功能描述:LED Driver with 1-Wire Dimming(3 LED) |
發布緊急采購，3分鐘左右您將得到回復。