- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL95310 (Intersil Corporation) Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface PDF資料下載
參數資料
| 型號： | ISL95310 |
| 廠商： | Intersil Corporation |
| 英文描述： | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| 中文描述： | 終端電壓為0V到13.2V，128絲錐向上/向下接口 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 135K |
| 代理商： | ISL95310 |
6
FN8083.0
May 6, 2005
A.C. Timing
Power Up and Down Requirements
In order to prevent unwanted tap position changes, or an
inadvertent store, bring the CS and INC high before or
concurrently with the V
CC
pin on power-up. The
potentiometer voltages must be applied after this sequence
is completed. During power-up, the data sheet parameters
for the DCP do not fully apply until 1ms after V
CC
reaches its
final value. The V
CC
ramp spec is always in effect.
Pin Descriptions
R
H
and R
L
The high (R
H
) and low (R
L
) terminals of the ISL95310 are
equivalent to the fixed terminals of a mechanical
potentiometer. The terminology of R
L
and R
H
references the
relative position of the terminal in relation to wiper movement
direction selected by the U/D input and not the voltage
potential on the terminal.
R
W
R
W
is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in nonvolatile memory when
CS is returned HIGH while the INC input is also HIGH. After
the store operation is complete the ISL95310 will be placed
in the low power standby mode until the device is selected
once again.
Principles of Operation
There are three sections of the ISL95310: the input control,
counter and decode section; the nonvolatile memory; and
the resistor array. The input control section operates just like
an up/down counter. The output of this counter is decoded to
turn on a single electronic switch connecting a point on the
resistor array to the wiper output. Under the proper
conditions the contents of the counter can be stored in
nonvolatile memory and retained for future use. The resistor
array is comprised of 127 individual resistors connected in
series. At either end of the array and between each resistor
is an electronic switch that transfers the potential at that
point to the wiper.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions. If
the wiper is moved several positions, multiple taps are
connected to the wiper for t
IW
(INC to V
W
change). The
R
TOTAL
value for the device can temporarily be reduced by
a significant amount if the wiper is moved several positions.
When the device is powered-down, the last wiper position
stored will be maintained in the nonvolatile memory. When
power is restored, the contents of the memory are recalled
and the wiper is set to the value last stored.
CS
INC
U/D
R
W
t
CI
t
IL
t
IH
t
CYC
t
ID
t
DI
t
IW
MI
(3)
t
IC
t
CPHS
t
F
t
R
10%
90%
90%
t
CPHNS
ISL95310
相關PDF資料 |
PDF描述 |
|---|---|
| ISL95310WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95310UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
| ISL95311 | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
| ISL95311WIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
| ISL95311UIU10Z | Terminal Voltage 0V to 13.2V, 128 Taps I2C Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL95310UIU10Z | 功能描述:IC XDCP 128-TAP 50KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95310UIU10Z-TK | 功能描述:IC XDCP 128-TAP 50KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95310WIU10Z | 功能描述:IC XDCP 128-TAP 10KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95310WIU10Z-TK | 功能描述:IC XDCP 128-TAP 10KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 標準包裝:3,000 系列:DPP 接片:32 電阻（歐姆）:10k 電路數:1 溫度系數:標準值 300 ppm/°C 存儲器類型:非易失 接口:3 線串行（芯片選擇，遞增，增/減） 電源電壓:2.5 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WFDFN 裸露焊盤 供應商設備封裝:8-TDFN（2x3） 包裝:帶卷 (TR) |
| ISL95311UIU10Z | 功能描述:IC XDCP 128-TAP 50KOHM 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:XDCP™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:256 電阻（歐姆）:100k 電路數:2 溫度系數:標準值 35 ppm/°C 存儲器類型:易失 接口:6 線串行（芯片選擇，遞增，增/減） 電源電壓:2.6 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。