- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9212IRZ (INTERSIL CORP) Charging System Safety Circuit PDF資料下載
參數資料
| 型號： | ISL9212IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Charging System Safety Circuit |
| 中文描述： | 1 A BATTERY CHARGE CONTROLLER, PDSO12 |
| 封裝： | 4 X 3 MM, ROHS COMPLIANT, PLASTIC, MO-229WGED-4, TDFN |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 527K |
| 代理商： | ISL9212IRZ |
9
FN9280.1
May 8, 2006
R
VB
Selection
The R
VB
prevents a large current from the VB pin to the
battery terminal, in case the ISL9212 fails. The
recommended value should be between 200k
Ω
to 1M
Ω
.
With 200k
Ω
resistance, the worst case current flowing from
the VB pin to the charger output is,
(30V - 4.2V)/200k
Ω
= 130
μ
A,
assuming the VB pin voltage is 30V under a failure mode
and the battery voltage is 4.2V. Such a small current can be
easily absorbed by the bias current of other components in
the handheld system. Increasing the R
VB
value reduces the
worst case current, but at the same time increases the error
for the 4.4V battery OVP threshold.
The error of the battery OVP threshold is the original
accuracy at the VB pin given in the Electrical Specification
plus the voltage built across the R
VB
by the VB pin leakage
current. The VB pin leakage current is less than 20nA, as
given in the Electrical Specification. With the 200k
Ω
resistor,
the worst-case additional error is 4mV and with a 1M
Ω
resistor, the worst-case additional error is 20mV.
Interfacing to MCU
The ISL9212 has the enable (EN) and the warning (WRN)
digital signals that can be interfaced to a microcontroller unit
(MCU). Both signals can be left floating if not used. When
interfacing to an MCU, it is highly recommended to insert a
resistor between the ISL9212 signal pin and the MCU GPIO
pin, as shown in Figure 24. The resistor creates an isolation
to limit the current, in case a high voltage shows up at the
ISL9212 pins under a failure mode. The recommended
resistance ranges from 10k
Ω
to 100k
Ω
. The selection of the
R
EN
is dependent on the IO voltage (VIO) of the MCU. R
EN
should be selected so that the ISL9212 EN pin voltage is
above the disable threshold when the GPIO output of the
MCU is high.
Capacitor Selection
The input capacitor (C1 in the Typical Application Circuit) is
for decoupling. Higher value reduces the voltage drop or the
over shoot during transients.
Two scenarios can cause the input voltage over shoot. The
first one is when the AC adapter is inserted live (hot
insertion) and the second one is when the current in the
power PFET of the ISL9212 has a step-down change. Figure
25 shows an equivalent circuit for the ISL9212 input. The
cable between the AC/DC converter output and the
handheld system input has a parasitic inductor. The parasitic
resistor is the lumped sum of various components, such as
the cable, the adapter output capacitor ESR, the connector
contact resistance, and so on.
During the load current step-down transient, the energy
stored in the parasitic inductor is used to charge the input
decoupling capacitor C2. The ISL9212 is designed to turn off
the power PFET slowly during the OCP, the battery OVP
event, and when the device is disabled via the EN pin.
Because of such design, the input over shoot during those
events is not significant. During an input OVP, however, the
PFET is turned in less than 1μs and can lead to significant
over shoot. Higher capacitance reduces this type of over
shoot.
FIGURE 23. LITHIUM-SAFE OPERATING REGIONS
5
0
1000
BATTERY VOLTAGE (V)
C
1
2
3
4
ISL9212
LIMITS
ISL6292C
LIMITS
6
FIGURE 24. DIGITAL SIGNAL INTERFACE BETWEEN ISL9212
AND MCU
WRN
R
5
Q
4
Q
5
EN
ISL9212
MCU
R
PU
R
WRN
R
EN
VIO
FIGURE 25. EQUIVALENT CIRCUIT FOR THE ISL9212 INPUT
AC/DC
ISL9212
ADAPTER
CABLE
HANDHELD SYSTEM
C1
L
R
C2
ISL9212
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9216 | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL9216IRZ | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL9217 | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL9217IRZ | 8 to 12 Cell Li-Ion Battery Overcurrent Protection and Analog Front End Chip Set |
| ISL95310 | Terminal Voltage 0V to 13.2V, 128 Taps Up/Down Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9212IRZ-T | 功能描述:IC SAFETY SYSTEM CHARGER 12-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| ISL9214 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger Accepting Two Power Sources |
| ISL9214AEVAL1Z | 功能描述:EVALUATION BOARD FOR ISL9214 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL9214AIRZ | 功能描述:IC BATTERY CHRGR LI-ION 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
發布緊急采購，3分鐘左右您將得到回復。