- 您現在的位置：買賣IC網 > PDF目錄384532 > ISL9208IRZ (INTERSIL CORP) Multi-Cell Li-ion Battery Pack OCP/Analog Front End PDF資料下載
參數資料
| 型號： | ISL9208IRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Multi-Cell Li-ion Battery Pack OCP/Analog Front End |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 24/29頁 |
| 文件大?。?/td> | 495K |
| 代理商： | ISL9208IRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁
24
FN6446.0
February 16, 2007
WRITE OPERATIONS
For a write operation, the device requires a slave byte and
an address byte. The slave byte specifies the particular
device on the I
2
C bus that the master is writing to. The
address specifies one of the registers in that device. After
receipt of each byte, the device responds with an
acknowledge, and awaits the next eight bits from the master.
After the acknowledge, following the transfer of data, the
master terminates the transfer by generating a stop
condition. See Figure 12.
When receiving data from the master, the value in the data
byte is transferred into the register specified by the address
byte on the falling edge of the clock following the 8th data bit.
After receiving the acknowledge after the data byte, the
device automatically increments the address. So, before
sending the stop bit, the master may send additional data to
the device without re-sending the slave and address bytes.
After writing to address 0AH, the address “wraps around” to
address 0. Do not continue to write to addresses higher than
address 08H, since these addresses access registers that
are reserved. Writing to these locations can result in
unexpected device operation.
Read Operations
Read operations are initiated in the same manner as write
operations with the exception that the last bit of the slave
byte is set to one. After the device acknowledges the register
address, it sends out one bit of data for each master clock.
After sending eight bits to the master, the master sends a
NACK (Not acknowledge) to the device, then sends a stop
bit. See Figure 13.
After sending the eighth data bit to the master, the device
automatically increments its internal address pointer. So the
master, instead of sending the stop bit, can send additional
clocks to read the contents of the next register-without
sending another slave and address byte. After reading from
address 9, the device address wraps around to 0, so
continued master clocks would allow an indefinite number of
reads from the device.
.
Register Protection
The Discharge Set, Charge Set, and Feature Set
configuration registers are write protected on initial power
up. In order to write to these registers it is necessary to set a
bit to enable each one. These write enable bits are in the
Write Enable register (Address 08H).
Write the FSETEN bit (Addr 8:bit 7) to “1” to enable changes
to the data in the Feature Set register (Address 7).
Write the CHSETEN bit (Addr 8:bit 6) to “1” to enable
changes to the data in the Feature Set register (Address 6).
Write the DISSETEN bit (Addr 8:bit 5) to “1” to enable
changes to the data in the Feature Set register (Address 5).
The microcontroller can reset these bits back to zero to
prevent inadvertent writes that change the operation of the
pack.
Operation State Machine
Figure 14 shows a device state machine which defines how
the ISL9208 responds to various conditions.
0
0 1 0 1
0 0
0
S
T
A
R
T
S
T
O
P
SLAVE
BYTE
REGISTER
ADDRESS
DATA
A
C
K
A
C
K
A
C
K
SDA BUS
S
F
S
S
F
M
FIGURE 12. WRITE SEQUENCE
ISL9208: SLAVE BYTE = 50H
1
0 1 0 1
0 0
0
S
T
A
R
T
S
T
O
P
SLAVE
BYTE
REGISTER
ADDRESS
DATA
A
C
K
A
C
K
N
A
C
K
SDA
BUS
S
F
S
S
F
M
FIGURE 13. READ SEQUENCE
ISL9208: SLAVE BYTE = 51H
ISL9208
相關PDF資料 |
PDF描述 |
|---|---|
| ISL9209B | Charging System Safety Circuit |
| ISL9209BIRZ | Charging System Safety Circuit |
| ISL9209 | Charging System Safety Circuit |
| ISL9209IRZ | Charging System Safety Circuit |
| ISL9209IRZ-T | Charging System Safety Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL9208IRZ-T | 功能描述:IC MULTI-CELL LI-ION PROT 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9209 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Charging System Safety Circuit |
| ISL9209B | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Charging System Safety Circuit |
| ISL9209BIRZ | 功能描述:IC SAFETY SYSTEM CHARGER 12-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL9209BIRZ-T | 功能描述:IC SAFETY SYSTEM CHARGER 12-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
發布緊急采購，3分鐘左右您將得到回復。