- 您現在的位置：買賣IC網 > PDF目錄383169 > ISL84544 (Intersil Corporation) 1024 x 36 synchronous FIFO Memory 120-HLQFP 0 to 70 PDF資料下載
參數資料
| 型號： | ISL84544 |
| 廠商： | Intersil Corporation |
| 元件分類： | DRAM |
| 英文描述： | 1024 x 36 synchronous FIFO Memory 120-HLQFP 0 to 70 |
| 中文描述： | 低電壓，單電源，雙路SPST，SPDT模擬開關 |
| 文件頁數： | 9/16頁 |
| 文件大?。?/td> | 336K |
| 代理商： | ISL84544 |
9
Detailed Description
The ISL84541–ISL84544 dual analog switches offer precise
switching capability from a single 2.7V to 12V supply with
low on-resistance (30
) and high speed operation
(t
ON
= 35ns, t
OFF
= 25ns). The devices are especially well
suited to portable battery powered equipment thanks to the
low operating supply voltage (2.7V), low power consumption
(5
μ
W), low leakage currents (100pA max), and the tiny
SOT-23 packaging. High frequency applications also benefit
from the wide bandwidth, and the very high off isolation and
crosstalk rejection.
Supply Sequencing And Overvoltage Protection
With any CMOS device, proper power supply sequencing is
required to protect the device from excessive input currents
which might permanently damage the IC. All I/O pins contain
ESD protection diodes from the pin to V+ and to GND (see
Figure 8). To prevent forward biasing these diodes, V+ must
be applied before any input signals, and input signal voltages
must remain between V+ and GND. If these conditions cannot
be guaranteed, then one of the following two protection
methods should be employed.
Logic inputs can easily be protected by adding a 1k
resistor
in series with the input (see Figure 8). The resistor limits the
input current below the threshold that produces permanent
damage, and the sub-microamp input current produces an
insignificant voltage drop during normal operation.
Adding a series resistor to the switch input defeats the
purpose of using a low R
ON
switch, so two small signal diodes
can be added in series with the supply pins to provide
overvoltage protection for all pins (see Figure 8). These
additional diodes limit the analog signal from 1V below V+ to
1V above GND. The low leakage current performance is
unaffected by this approach, but the switch resistance may
increase, especially at low supply voltages.
Power-Supply Considerations
The ISL8454X construction is typical of most CMOS analog
switches, except that they have only two supply pins: V+ and
GND. V+ and GND drive the internal CMOS switches and set
their analog voltage limits. Unlike switches with a 13V
maximum supply voltage, the ISL8454X 15V maximum supply
voltage provides plenty of room for the 10% tolerance of 12V
supplies, as well as room for overshoot and noise spikes.
The minimum recommended supply voltage is 2.7V. It is
important to note that the input signal range, switching times,
and on-resistance degrade at lower supply voltages. Refer to
the electrical specification tables and
Typical Performance
curves for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the logic levels to switched V+ and
GND signals to drive the analog switch gate terminals.
This family of switches cannot be operated with bipolar
supplies, because the input switching point becomes negative
in this configuration.
Logic-Level Thresholds
This switch family is TTL compatible (0.8V and 2.4V) over a
supply range of 3V to 11V (see Figure 15). At 12V the V
IH
level is about 2.5V. This is still below the TTL guaranteed
high output minimum level of 2.8V, but noise margin is
reduced. For best results with a 12V supply, use a logic
family the provides a V
OH
greater than 3V.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation.
High-Frequency Performance
In 5
0
systems, signal response is reasonably flat even past
300MHz (see Figure 16). Figure 16 also illustrates that the
frequency response is very consistent over a wide V+ range,
and for varying analog signal levels.
An off switch acts like a capacitor and passes higher
frequencies with less attenuation, resulting in signal
feedthrough from a switch’s input to its output. Off Isolation
is the resistance to this feedthrough, while Crosstalk
indicates the amount of feedthrough from one switch to
another. Figure 17 details the high Off Isolation and
Crosstalk rejection provided by this family. At 10MHz, off
isolation is about 50dB in 5
0
systems, decreasing
approximately 20dB per decade as frequency increases.
Higher load impedances decrease Off Isolation and
Crosstalk rejection due to the voltage divider action of the
switch OFF impedance and the load impedance.
Leakage Considerations
Reverse ESD protection diodes are internally connected
between each analog-signal pin and both V+ and GND.
One of these diodes conducts if any analog signal exceeds
V+ or GND.
Virtually all the analog leakage current comes from the ESD
diodes to V+ or GND. Although the ESD diodes on a given
signal pin are identical and therefore fairly well balanced,
GND
V
COM
V
NO or NC
OPTIONAL PROTECTION
DIODE
V+
IN
X
OPTIONAL PROTECTION
DIODE
OPTIONAL
PROTECTION
RESISTOR
FIGURE 8. OVERVOLTAGE PROTECTION
ISL84541, ISL84542, ISL84543, ISL84544
相關PDF資料 |
PDF描述 |
|---|---|
| ISL84542CP | Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541CB | Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541IP | Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541IU | Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
| ISL84541IH-T | Low-Voltage, Single Supply, Dual SPST, SPDT Analog Switches |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL84544CB | 功能描述:IC SWITCH SPDT 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:- 電路:2 x SPST 導通狀態電阻:20 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3 V ~ 5.5 V 電流 - 電源:4.1mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:帶卷 (TR) |
| ISL84544CB-T | 功能描述:IC SWITCH SPDT 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:- 電路:2 x SPST 導通狀態電阻:20 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3 V ~ 5.5 V 電流 - 電源:4.1mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:帶卷 (TR) |
| ISL84544CBZ | 功能描述:IC SWITCH SPDT 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL84544CBZ-T | 功能描述:IC SWITCH SPDT 8SOIC RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL84544CP | 功能描述:IC SWITCH SPDT 8DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:- 電路:2 x SPST 導通狀態電阻:20 歐姆 電壓電源:單電源 電壓 - 電源，單路/雙路(±):3 V ~ 5.5 V 電流 - 電源:4.1mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。