- 您現在的位置：買賣IC網 > PDF目錄383159 > ISL6569CBZ (INTERSIL CORP) Multi-Phase PWM Controller PDF資料下載
參數資料
| 型號： | ISL6569CBZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multi-Phase PWM Controller |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封裝： | LEAD FREE, PLASTIC, MS-013-AD, SOIC-24 |
| 文件頁數： | 20/22頁 |
| 文件大?。?/td> | 497K |
| 代理商： | ISL6569CBZ |
20
FN9085.7
December 29, 2004
For a two phase design, use Figure 16 to determine the
input-capacitor RMS current requirement given the duty
cycle, maximum sustained output current (I
O
), and the ratio
of the combined peak-to-peak inductor current (I
C,PP
) to I
O
.
Select a bulk capacitor with a ripple current rating which will
minimize the total number of input capacitors required to
support the RMS current calculated. The voltage rating of
the capacitors should also be at least 1.25 times greater
than the maximum input voltage.
Layout Considerations
The following multi-layer printed circuit board layout strategies
minimize the impact of board parasitics on converter
performance. The following sections highlight some important
practices which should not be overlooked during the layout
process.
Component Placement
Within the allotted implementation area, orient the switching
components first. The switching components are the most
critical because they switch large amounts of energy and
tend to generate large amounts of noise. How the switching
components are placed should also take into account power
dissipation. Align the output inductors and MOSFETs such
that space between the components is minimized while
creating the PHASE plane. Place the Intersil HIP660X
drivers as close as possible to the MOSFETs they control to
reduce the parasitics due to trace length between critical
driver input and output signals. If possible, duplicate the
same placement of switching components for each phase.
Next, place the input and output capacitors. Position one
high-frequency ceramic input capacitor next to each upper
MOSFET drain. Place the bulk input capacitors as close to
the upper MOSFET drains as dictated by the component
size and dimensions. Long distances between input
capacitors and MOSFET drains results in too much trace
inductance and a reduction in capacitor performance. Locate
the output capacitors between the inductors and the load,
while keeping them in close proximity around the
microprocessor socket.
The ISL6569 can be placed off to one side or centered
relative to the individual phase switching components.
Routing of sense lines and PWM signals will guide final
placement. Critical small signal components to place close
to the controller include the ISEN resistors, R
T
resistor,
feedback resistor, and compensation components.
Bypass capacitors for the ISL6569 and HIP660X driver bias
supplies must be placed next to their respective pins. Stray
trace parasitics will reduce their effectiveness.
Plane Allocation and Routing
Dedicate one solid layer, usually a middle layer, for a ground
plane. Make all critical component ground connections with
vias to this plane. Dedicate one additional layer for power
planes; breaking the plane up into smaller islands of
common voltage. Use the remaining layers for small signal
wiring.
Route PHASE planes of copper filled polygons on the top
and bottom once the switching component placement is set.
Size the trace width between the driver gate pins and the
MOSFET gates to carry 1A of current. When routing
components in the switching path, use short wide traces to
reduce the associated parasitics.
0.3
0.1
0
0.2
I
R
/
O
)
FIGURE 16. NORMALIZED INPUT-CAPACITOR RMS CURRENT
VS DUTY CYCLE FOR 2-PHASE CONVERTER
0
0.4
1.0
0.2
0.6
0.8
DUTY CYCLE (V
IN
/ V
O
)
I
C,PP
= 0
I
C,PP
= 0.5 I
O
I
C,PP
= 0.75 I
O
ISL6569
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6569CR | Multi-Phase PWM Controller |
| ISL6571EVAL1 | Complementary MOSFET Driver and Synchronous Half-Bridge Switch |
| ISL6571CR-T | Complementary MOSFET Driver and Synchronous Half-Bridge Switch |
| ISL6571CR | Complementary MOSFET Driver and Synchronous Half-Bridge Switch |
| ISL6571CRZ | Complementary MOSFET Driver and Synchronous Half-Bridge Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6569CBZ-T | 功能描述:IC REG CTRLR DIVIDER PWM 24-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6569CR | 功能描述:IC REG CTRLR DIVIDER PWM 32-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6569CR-T | 功能描述:IC REG CTRLR DIVIDER PWM 32-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:100% 電源電壓:8.2 V ~ 30 V 降壓:無 升壓:無 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:0°C ~ 70°C 封裝/外殼:8-DIP（0.300"，7.62mm） 包裝:管件 產品目錄頁面:1316 (CN2011-ZH PDF) |
| ISL6569CRZ | 功能描述:IC REG CTRLR DIVIDER PWM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6569CRZ-T | 功能描述:IC REG CTRLR DIVIDER PWM 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。