參數資料
型號： ISL6566CRZA-T
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications
中文描述： SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40
封裝： 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220-VJJD, MLFP, QFN-40
文件頁數： 19/28頁
文件大小： 799K
代理商： ISL6566CRZA-T
19
FN9178.3
July 25, 2005
If VSEN or RGND become opened, VDIFF falls, causing the
duty cycle to increase and the output voltage on IREF to
increase. If the voltage on IREF exceeds “VDIFF+1V”, the
controller will shut down. Once the voltage on IREF falls
below “VDIFF+1V”, the ISL6566 will restart at the beginning
of soft-start.
Overcurrent Protection
The ISL6566 detects overcurrent events by comparing the
droop voltage, V
DROOP
, to the OCSET voltage, V
OCSET
, as
shown in Figure 13. The droop voltage, set by the external
current sensing circuitry, is proportional to the output current
as shown in Equation 7. A constant 100
μ
A flows through
R
OCSET
, creating the OCSET voltage. When the droop
voltage exceeds the OCSET voltage, the overcurrent
protection circuitry activates. Since the droop voltage is
proportional to the output current, the overcurrent trip level,
I
MAX
, can be set by selecting the proper value for R
OCSET
,
as shown in Equation 14.
Once the output current exceeds the overcurrent trip level,
V
DROOP
will exceed V
OCSET
, and a comparator will trigger the
converter to begin overcurrent protection procedures. At the
beginning of overcurrent shutdown, the controller turns off both
upper and lower MOSFETs. The system remains in this state
for a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-start
(as shown in Figure 14). If the fault remains, the trip-retry cycles
will continue indefinitely until either the controller is disabled or
the fault is cleared. Note that the energy delivered during trip-
retry cycling is much less than during full-load operation, so
there is no thermal hazard.
General Design Guide
This design guide is intended to provide a high-level
explanation of the steps necessary to create a multi-phase
power converter. It is assumed that the reader is familiar with
many of the basic skills and techniques referenced below. In
addition to this guide, Intersil provides complete reference
designs that include schematics, bills of materials, and example
board layouts for all common microprocessor applications.
Power Stages
The first step in designing a multi-phase converter is to
determine the number of phases. This determination
depends heavily on the cost analysis which in turn depends
on system constraints that differ from one design to the next.
Principally, the designer will be concerned with whether
components can be mounted on both sides of the circuit
board, whether through-hole components are permitted, the
total board space available for power-supply circuitry, and
the maximum amount of load current. Generally speaking,
the most economical solutions are those in which each
phase handles between 25 and 30A. All surface-mount
designs will tend toward the lower end of this current range.
If through-hole MOSFETs and inductors can be used, higher
per-phase currents are possible. In cases where board
space is the limiting constraint, current can be pushed as
high as 40A per phase, but these designs require heat sinks
and forced air to cool the MOSFETs, inductors and heat-
dissipating surfaces.
MOSFETS
The choice of MOSFETs depends on the current each
MOSFET will be required to conduct, the switching frequency,
the capability of the MOSFETs to dissipate heat, and the
availability and nature of heat sinking and air flow.
LOWER MOSFET POWER CALCULATION
The calculation for power loss in the lower MOSFET is
simple, since virtually all of the loss in the lower MOSFET is
due to current conducted through the channel resistance
(r
DS(ON)
). In Equation 15, I
M
is the maximum continuous
output current, I
PP
is the peak-to-peak inductor current (see
Equation 1), and d is the duty cycle (V
OUT
/V
IN
).
An additional term can be added to the lower-MOSFET loss
equation to account for additional loss accrued during the
dead time when inductor current is flowing through the
lower-MOSFET body diode. This term is dependent on the
diode forward voltage at I
M
, V
D(ON)
, the switching
frequency, f
S
, and the length of dead times, t
d1
and t
d2
, at
the beginning and the end of the lower-MOSFET conduction
interval respectively.
The total maximum power dissipated in each lower MOSFET
is approximated by the summation of P
LOW,1
and P
LOW,2
.
R
OCSET
I
R
DCR
S
---------------------------------------------------------
=
(EQ. 14)
0A
0V
2ms/DIV
OUTPUT CURRENT, 50A/DIV
FIGURE 14. OVERCURRENT BEHAVIOR IN HICCUP MODE
F
SW
= 500kHz
OUTPUT VOLTAGE,
500mV/DIV
P
LOW 1
r
DS ON
)
I
M
N
-----
2
1
d
–
(
)
I
,
-------------12
2
1
d
–
(
)
+
=
(EQ. 15)
P
LOW 2
V
D ON
)
f
S
I
M
N
-----
I
---2
+
t
d1
I
M
N
-----
I
---2
–
t
d2
+
=
(EQ. 16)
ISL6566
相關PDF資料
PDF描述
ISL6566IRZA-T Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications
ISL6567CRZ Multipurpose Two-Phase Buck PWM Controller with Integrated MOSFET Drivers
ISL6567EVAL1 Multipurpose Two-Phase Buck PWM Controller with Integrated MOSFET Drivers
ISL6567CRZ-T Multipurpose Two-Phase Buck PWM Controller with Integrated MOSFET Drivers
ISL6567 Dual Low-Noise Wide-Bandwidth Precision Amplifier 8-SOIC -40 to 85
相關代理商/技術參數
參數描述
ISL6566CRZA-TR5184 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
ISL6566CRZR5184 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件
ISL6566CRZ-T 功能描述:IC CTLR PWM BUCK 3PHASE 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
ISL6566CRZ-TR5184 功能描述:IC CTRLR PWM 3PHASE BUCK 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
ISL6566EVAL1 功能描述:EVAL BOARD 1 FOR ISL6566 RoHS:否 類別:編程器，開發系統 >> 評估板 - 線性穩壓器 (LDO) 系列:* 產品變化通告:1Q2012 Discontinuation 30/Mar/2012 設計資源:NCP590MNDPTAGEVB Gerber Files 標準包裝:1 系列:- 每 IC 通道數:2 - 雙 輸出電壓:1.8V，2.8V 電流 - 輸出:300mA 輸入電壓:2.1 ~ 5.5 V 穩壓器類型:正，固定式 工作溫度:-40°C ~ 85°C 板類型:完全填充 已供物品:板 已用 IC / 零件:NCP590MNDP 其它名稱:NCP590MNDPTAGEVB-NDNCP590MNDPTAGEVBOS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*