- 您現在的位置：買賣IC網 > PDF目錄384526 > ISL6564AIRZ (INTERSIL CORP) Multiphase PWM Controller with Linear 6-Bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing PDF資料下載
參數資料
| 型號： | ISL6564AIRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Multiphase PWM Controller with Linear 6-Bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220, QFN-40 |
| 文件頁數： | 12/28頁 |
| 文件大?。?/td> | 636K |
| 代理商： | ISL6564AIRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
12
FN6285.1
March 20, 2007
The output capacitors conduct the ripple component of the
inductor current. In the case of multiphase converters, the
capacitor current is the sum of the ripple currents from each
of the individual channels. Compare Equation 1 to the
expression for the peak-to-peak current after the summation
of N symmetrically phase-shifted inductor currents in
Equation 2. Peak-to-peak ripple current decreases by an
amount proportional to the number of channels. Output-
voltage ripple is a function of capacitance, capacitor
equivalent series resistance (ESR), and inductor ripple
current. Reducing the inductor ripple current allows the
designer to use fewer or less costly output capacitors.
Another benefit of interleaving is to reduce input ripple
current. Input capacitance is determined in part by the
maximum input ripple current. Multiphase topologies can
improve overall system cost and size by lowering input ripple
current and allowing the designer to reduce the cost of input
capacitance. The example in Figure 2 illustrates input
currents from a three-phase converter combining to reduce
the total input ripple current.
The converter depicted in Figure 2 delivers 36A to a 1.5V load
from a 12V input. The RMS input capacitor current is 5.9A.
Compare this to a single-phase converter also stepping down
12V to 1.5V at 36A. The single-phase converter has 11.9A
RMS input capacitor current. The single-phase converter
must use an input capacitor bank with twice the RMS current
capacity as the equivalent three-phase converter.
Figures 21, 22 and 23 in the section entitled
Input Capacitor
Selection
can be used to determine the input-capacitor RMS
current based on load current, duty cycle, and the number of
channels. They are provided as aids in determining the
optimal input capacitor solution. Figure 24 shows the single
phase input-capacitor RMS current for comparison.
PWM Operation
The timing of each converter leg is set by the number of
active channels. The default channel setting for the
ISL6564A is four. One switching cycle is defined as the time
between PWM1 pulse termination signals. The pulse
termination signal is an internally generated clock signal
which triggers the falling edge of PWM1. The cycle time of
the pulse termination signal is the inverse of the switching
frequency set by the resistor between the FS pin and
ground. Each cycle begins when the clock signal commands
the channel 1 PWM output to go low. The PWM1 transition
signals the channel-1 MOSFET driver to turn off the
channel 1 upper MOSFET and turn on the channel 1
synchronous MOSFET. In the default channel configuration,
the PWM2 pulse terminates 1/4 of a cycle after PWM1. The
PWM3 output follows another 1/4 of a cycle after PWM2.
PWM4 terminates another 1/4 of a cycle after PWM3.
If PWM3 is connected to VCC, two channel operation is
selected and the PWM2 pulse terminates 1/2 of a cycle later.
Connecting PWM4 to VCC selects three channel operation
and the pulse-termination times are spaced in 1/3 cycle
increments. Connecting both PWM3 and PWM4 to VCC
selects single-channel operation.
Once a PWM signal transitions low, it is held low for a
minimum of 1/3 cycle. This forced off time is required to
ensure an accurate current sample. Current sensing is
described in the next section. After the forced off time
expires, the PWM output is enabled. The PWM output state
is driven by the position of the error amplifier output signal,
V
COMP
, minus the current correction signal relative to the
sawtooth ramp as illustrated in Figure 7. When the modified
V
COMP
voltage crosses the sawtooth ramp, the PWM output
transitions high. The MOSFET driver detects the change in
state of the PWM signal and turns off the synchronous
MOSFET and turns on the upper MOSFET. The PWM signal
will remain high until the pulse termination signal marks the
beginning of the next cycle by triggering the PWM signal low.
Current Sampling
During the forced off-time following a PWM transition low,
the associated channel current sense amplifier uses the
ISEN inputs to reproduce a signal proportional to the
inductor current, I
L
. No matter the current sense method, the
sense current, I
SEN
, is simply a scaled version of the
inductor current. Coincident with the falling edge of the PWM
signal, the sample and hold circuitry samples I
SEN
, as
illustrated in Figure 3. The sample window hold time, t
HOLD
,
is fixed and equal to 1/3 of the switching period, t
SW
.
t
SW
Therefore, the sample current, I
n
, is proportional to the
output current and held for one switching cycle. The sample
current is used for current balance, load-line regulation, and
overcurrent protection.
FIGURE 2. CHANNEL INPUT CURRENTS AND INPUT-
CAPACITOR RMS CURRENT FOR 3-PHASE
CONVERTER
CHANNEL 1
INPUT CURRENT
10A/DIV
CHANNEL 2
INPUT CURRENT
10A/DIV
CHANNEL 3
INPUT CURRENT
10A/DIV
INPUT-CAPACITOR CURRENT, 10A/DIV
1μs/DIV
I
C PP
,
V
--------------------Lf
N V
S
V
IN
–
(
)
V
OUT
=
(EQ. 2)
t
HOLD
----------
-----------------
=
=
(EQ. 3)
ISL6564A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6566CRR5184 | Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6566CR-TR5184 | Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6566CRZAR5184 | Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6566CRZA-TR5184 | Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
| ISL6566CRZR5184 | Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6564AIRZ-T | 功能描述:IC REG CTRLR BUCK PWM VM 40-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6564CR | 功能描述:IC REG CTRLR BUCK PWM VM 40-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6564CR-T | 功能描述:IC REG CTRLR BUCK PWM VM 40-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| ISL6564CRZ | 功能描述:電流型 PWM 控制器 LEAD-FREE MULTI-PHASE PWM CONTROLLER W/ 0.525-1.3 VID RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6564CRZ-T | 功能描述:電流型 PWM 控制器 LEAD-FREE MULTI-PHASE PWM CONTROLLER W/ 0.525-1.3 VID, T&R RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。