參數資料
型號： ISL6551AR
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： ZVS Full Bridge PWM Controller
中文描述： DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC28
封裝： 6 X 6 MM, PLASTIC, MO-220VJJC, QFN-28
文件頁數： 14/26頁
文件大?。?/td> 604K
代理商： ISL6551AR
14
FN9066.5
January 3, 2006
Ramp Adjust (R_RA, ISENSE)
- The ramp adjust block adds an offset component
(200mV) and a slope adjust component to the ISENSE
signal before processing it at the PWM Logic block, as
shown in Figure 9. This ensures that the ramp voltage is
always higher than the OAGS (ground sensing opamp)
minimum voltage to achieve a “zero” state.
- It is critical that the input signal to ISENSE decays to
zero prior to or during the clock dead time. The level-
shifting and capacitive summing circuits in the RAMP
ADJUST block are reset during the dead time. Any input
signal transitions that occur after the rising edge of CLK
and prior to the rising edge of RESDLY can cause
severe errors in the signal reaching the PWM
comparator.
- Typical ramp values are hundreds of mV over the period
on a 3V full scale current. Too much ramp makes the
controller look like a voltage mode PWM, and too little
ramp leads to noise issues (jitter). The amount of ramp
(Vramp), as shown in Figure 9, is programmed with the
R_RA resistor and can be calculated with Equation 10.
- The voltage representation of the current flowing
through the power train at ISENSE pin is normally
scaled such that the desired peak current is less than or
equal to Vclamp-200mV-Vramp, where the clamping
voltage is set at the CSS pin.
SYNC Outputs (SYNC1, SYNC2)
- SYNC1 and SYNC2 are the gate control signals for the
output synchronous rectifiers. They are biased by VDD
and are capable of driving capacitive loads up to 20pF
at 1MHz clock frequency (500kHz switching frequency).
These outputs are turned off sooner than the turn-off at
UPPER1 and UPPER2 by the clock dead time, DT.
- Inverting both SYNC signals or both LOWER signals is
another possible way to control the drivers of the
synchronous rectifiers. When using these drive
schemes, the user should understand the issues that
might occur in his/her applications, especially the
impacts on current share operation and light load
operation. Refer to application note AN1002 for more
details.
- External high current drivers controlled by the
synchronous signals are required to drive the
synchronous rectifiers. A pulse transformer is required
to pass the drive signals to the secondary side if the IC
is used in a primary control system.
Share Support (SHARE, CS_COMP)
- The unit with the highest reference is the master. Other
units, as slaves, adjust their references via a source
resistor to match the master reference sharing the load
current. The source resistor is typically 1k
connecting
the EANI pin and the OUTPUT REFERENCE (external
reference or BGREF), as shown in Figure 10. The share
bus represents a 30k
resistive load per unit, up to 10
units.
- The output (ADJ) of “Operational Transconductance
Amplifier (OTA)” can only pull high and it is floating while
in master mode. This ensures that no current is sourced
to the OUTPUT REFERENCE when the IC is working
by itself.
- The slave units attempt to drive their error amplifier
voltage to be within a pre-determined offset (30mV
typical) of the master error voltage (the share bus). The
current-share error is nominally (30mV/EAO)*100%
assuming no other source of error. With a 2.5V full load
error amp voltage, the current-share error at full load
would be -1.2% (slaves relative to master).
- The bandwidth of the current sharing loop should be
much lower than that of the voltage loop to eliminate
noise pick-up and interactions between the voltage
regulation loop and the current loop. A 0.1
μ
F capacitor
is recommended between CS_COMP and VSS pins to
achieve a low current sharing loop bandwidth (100Hz to
500Hz).
(EQ. 10)
V
ramp
= BGREF x dt /(R_RA x 500E-12) (V)
where dt = Duty Cycle / Fsw - t
LEB
(s). Duty cycle is
discussed in detail in application note AN1002.
-
+
OTA
ADJ
+
-
+
-
EAO
CS_COMP
0.1
μ
F
1K
OUTPUT
REFERENCE
EANI
(+)
SHARE
30K
30mV
FIGURE 10. SIMPLIFIED CURRENT SHARE CIRCUIT
ISL6551
相關PDF資料
PDF描述
ISL6551IRZ ZVS Full Bridge PWM Controller
ISL6564A Multiphase PWM Controller with Linear 6-Bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing
ISL6564ACRZ Multiphase PWM Controller with Linear 6-Bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing
ISL6564AIRZ Multiphase PWM Controller with Linear 6-Bit DAC Capable of Precision rDS(ON) or DCR Differential Current Sensing
ISL6566CRR5184 Three-Phase Buck PWM Controller with Integrated MOSFET Drivers for VRM9, VRM10, and AMD Hammer Applications
相關代理商/技術參數
參數描述
ISL6551AR-T 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述:
ISL6551ARZ 功能描述:IC REG CTRLR FLYBACK PWM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6551ARZ-T 功能描述:IC REG CTRLR FLYBACK PWM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR)
ISL6551EVAL1 功能描述:EVALUATION BOARD ISL6551 RoHS:否 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
ISL6551IB 功能描述:電流型 PWM 控制器 FULL BRIDGE RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*