參數資料
型號： ISL6549CBZ
廠商： INTERSIL CORP
元件分類： 穩壓器
英文描述： Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
中文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO14
封裝： ROHS COMPLIANT, PLASTIC, MS-012AB, SOIC-14
文件頁數： 12/18頁
文件大?。?/td> 420K
代理商： ISL6549CBZ
12
FN9168.2
September 22, 2006
A stable control loop has a gain crossing with close to a
-20dB/decade slope and a phase margin greater than 45°.
Include worst case component variations when determining
phase margin. The mathematical model presented makes a
number of approximations and is generally not accurate at
frequencies approaching or exceeding half the switching
frequency. When designing compensation networks, select
target crossover frequencies in the range of 10% to 30% of
the switching frequency, F
SW
.
Linear Controller Feedback Compensation
For most situations, no external compensation is required for
the linear output. As long as the output capacitor (C
OUT2
) is
large (>100μF) and so is its ESR (>20mW), then it should be
stable for loads as low as 10mA up to at least 4A. If smaller
values of capacitance and/or ESR are desired, then special
considerations may be required to add external
compensation (as shown in Figure 8).
Component Selection Guidelines
Output Inductor Selection
The output inductor is selected to meet the output voltage
ripple requirements and minimize the converter’s response
time to the load transient. The inductor value determines the
converter’s ripple current and the ripple voltage is a function of
the ripple current. The ripple voltage and current are
approximated by Equation 10.
Increasing the value of inductance reduces the ripple current
and voltage. However, the large inductance values reduce the
converter’s response time to a load transient (and usually
increases the DCR of the inductor, which decreases the
efficiency). Increasing the switching frequency (F
SW
) for a
given inductor also reduces the ripple current and voltage.
One of the parameters limiting the converter’s response to a
load transient is the time required to change the inductor
current. Given a sufficiently fast control loop design, the
ISL6549 will provide either 0% or 100% duty cycle in
response to a load transient. The response time is the time
required to slew the inductor current from an initial current
value to the transient current level. During this interval, the
difference between the inductor current and the transient
current level must be supplied by the output capacitor.
Minimizing the response time can minimize the output
capacitance required.
The response time to a transient is different for the application
of load and the removal of load. Equation 11 gives the
approximate response time interval for application and
removal of a transient load:
where: I
TRAN
is the transient load current step, t
RISE
is the
response time to the application of load, and t
FALL
is the
response time to the removal of load. With a +5V input
source, the worst case response time can be either at the
application or removal of load and dependent upon the output
voltage setting. Be sure to check both of these equations at
the minimum and maximum output levels for the worst case
response time.
Output Capacitors Selection
An output capacitor is required to filter the output and supply
the load transient current. The filtering requirements are a
function of the switching frequency and the ripple current. The
load transient requirements are a function of the slew rate
(di/dt) and the magnitude of the transient load current. These
requirements are generally met with a mix of capacitors and
careful layout.
Modern microprocessors produce transient load rates above
1A/ns. High frequency capacitors initially supply the transient
and slow the current load rate seen by the bulk capacitors.
The bulk filter capacitor values are generally determined by
the ESR (effective series resistance) and voltage rating
requirements rather than actual capacitance requirements.
High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements. And keep in mind that not all
applications have the same requirements; some may need
many ceramic capacitors in parallel; others may need only one.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors.
The bulk capacitor’s ESR will determine the output ripple
voltage and the initial voltage drop after a high slew-rate
0
F
P1
F
Z2
OPEN LOOP E/A GAIN
F
Z1
F
P2
F
LC
F
CE
COMPENSATION GAIN
CLOSED LOOP GAIN
G
FREQUENCY
MODULATOR GAIN
FIGURE 11. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
20
d
OSC
V
IN
--------V
log
20
R1
log
LOG
L
F
0
G
MOD
G
FB
G
CL
V
OUT
=
I x ESR
I =
V
- V
SW
-------------------------------
V
IN
---------------
(EQ. 10)
t
FALL
L
------------------------------
I
OUT
×
=
t
RISE
L
IN
I
OUT
×
–
-------------------------------
=
(EQ. 11)
ISL6549
相關PDF資料
PDF描述
ISL6549CR Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
ISL6549CRZ Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
ISL6549HI-EVAL1 Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
ISL6549IAZ Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
ISL6549IBZ Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
相關代理商/技術參數
參數描述
ISL6549CBZR5194 制造商:Intersil Corporation 功能描述:
ISL6549CBZR5213 功能描述:IC REG DL BCK/LINEAR 14-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
ISL6549CBZ-T 功能描述:DC/DC 開關控制器 SINGLE 12V SUPPLY DLG 14LD N RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
ISL6549CBZ-TR5194 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述:
ISL6549CBZ-TR5213 制造商:Intersil Corporation 功能描述:DC DC CNTRLR DUAL-OUT SYNC BUCK/W/PWM 1V TO 12V 14SOIC N - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*