- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6445 (Intersil Corporation) 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller PDF資料下載
參數資料
| 型號： | ISL6445 |
| 廠商： | Intersil Corporation |
| 英文描述： | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| 中文描述： | 1.4MHz的雙路，180 °異相，降壓型PWM控制器 |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 353K |
| 代理商： | ISL6445 |
11
FN9230.0
September 9, 2005
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
that shuts the IC down when a die temperature of 150°C is
reached. Normal operation resumes when the die
temperatures drops below 130°C through the initiation of a
full soft-start cycle.
Feedback Loop Compensation
To reduce the number of external components and to
simplify the process of determining compensation
components, both PWM controllers have internally
compensated error amplifiers. To make internal
compensation possible several design measures were
taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
derived from the voltage drop across the lower MOSFET
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r
DS(ON)
.
Choosing R
CS
to provide 32μA of current to the current
sample and hold circuitry is recommended but values down
to 2μA and up to 100μA can be used.
Due to the current loop feedback, the modulator has a single
pole response with -20dB slope at a frequency determined
by the load.
where R
O
is load resistance and C
O
is load capacitance. For
this type of modulator, a Type 2 compensation circuit is
usually sufficient.
Figure 16 shows a Type 2 amplifier and its response along
with the responses of the current mode modulator and the
converter. The Type 2 amplifier, in addition to the pole at
origin, has a zero-pole pair that causes a flat gain region at
frequencies in between the zero and the pole.
The zero frequency, the amplifier high-frequency gain, and
the modulator gain are chosen to satisfy most typical
applications. The crossover frequency will appear at the
point where the modulator attenuation equals the amplifier
high frequency gain. The only task that the system designer
has to complete is to specify the output filter capacitors to
position the load main pole somewhere within one decade
lower than the amplifier zero frequency. With this type of
compensation plenty of phase margin is easily achieved due
to zero-pole pair phase ‘boost’.
Conditional stability may occur only when the main load pole
is positioned too much to the left side on the frequency axis
due to excessive output filter capacitance. In this case, the
ESR zero placed within the 1.2kHz to 30kHz range gives
some additional phase ‘boost’. Some phase boost can also
be achieved by connecting capacitor C
Z
in parallel with the
upper resistor R1 of the divider that sets the output voltage
value. Please refer to the output inductor and capacitor
selection sections for further details.
Layout Guidelines
Careful attention to layout requirements is necessary for
successful implementation of a ISL6445 based DC/DC
converter. The ISL6445 switches at a very high frequency
and therefore the switching times are very short. At these
switching frequencies, even the shortest trace has
significant impedance. Also the peak gate drive current rises
significantly in extremely short time. Transition speed of the
current from one device to another causes voltage spikes
across the interconnecting impedances and parasitic circuit
elements. These voltage spikes can degrade efficiency,
generate EMI, increase device overvoltage stress and
ringing. Careful component selection and proper PC board
layout minimizes the magnitude of these voltage spikes.
R
CS
I
---------------------------------------------
(
)
R
)
(
)
≥
F
PO
2
π
R
O
C
O
--------------------------------
,
=
F
Z
2
1
------------------------------
6kHz
=
=
F
P
2
R
1
C
2
------------------------------
600kHz
=
=
FIGURE 16. FEEDBACK LOOP COMPENSATION
R1
R2
C1
C2
F
PO
F
Z
F
P
F
C
MODULATOR
EA
CONVERTER
TYPE 2 EA
G
EA
= 18dB
G
M
= 17.5dB
ISL6445
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6445IAZ | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ-TK | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6455 | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
| ISL6455A | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
| ISL6504CB | Multiple Linear Power Controller with ACPI Control Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6445EVAL3Z | 功能描述:EVALUATION BOARD FOR ISL6445 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6445IAZ | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6445IAZS2695 | 制造商:Intersil Corporation 功能描述: |
| ISL6445IAZ-TK | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6445IAZ-TKS2645 | 制造商:Intersil Corporation 功能描述:DC DC CNTRLR DUAL-OUT STEP DOWN 4.5V TO 24V 24QSOP W - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。