- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6443 (Intersil Corporation) 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) PDF資料下載
參數資料
| 型號： | ISL6443 |
| 廠商： | Intersil Corporation |
| 英文描述： | 300kHz Dual, 180° Out-of-Phase, Step-Down PWM and Single Linear Controller(兩路300kHz，180°異相，降壓PWM外加一路線性控制器) |
| 中文描述： | 300kHz的雙路，180 °異相，降壓型PWM和線性控制器單（兩路為300kHz，180 °異相，降壓的PWM外加一路線性控制器） |
| 文件頁數： | 13/18頁 |
| 文件大小： | 341K |
| 代理商： | ISL6443 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁
13
FN9044.2
August 9, 2006
where, I
OC
is the desired overcurrent protection threshold,
and R
CS
is a value of the current sense resistor connected
to the ISENx pin. If an overcurrent is detected for 2
consecutive clock cycles then the IC enters a hiccup mode
by turning off the gate drivers and entering into soft-start.
The IC will cycle 2 times through soft-start before trying to
restart. The IC will continue to cycle through soft-start until
the overcurrent condition is removed. Hiccup mode is active
during soft-start so care must be taken to ensure that the
peak inductor current does not exceed the overcurrent
threshold during soft-start.
Because of the nature of this current sensing technique, and
to accommodate a wide range of r
DS(ON)
variations, the
value of the overcurrent threshold should represent an
overload current about 150% to 180% of the maximum
operating current. If more accurate current protection is
desired place a current sense resistor in series with the
lower MOSFET source.
Over-Temperature Protection
The IC incorporates an over-temperature protection circuit
that shuts the IC down when a die temperature of 150°C is
reached. Normal operation resumes when the die
temperatures drops below 130°C through the initiation of a
full soft-start cycle.
Implementing Synchronization
The SYNC pin may be used to synchronize two or more
controllers. When the SYNC pins of two controllers are
connected together, one controller becomes the master and
the other controller synchronizes to the master. A pull-down
resistor is required and must be sized to provide a low
enough time constant to pass the SYNC pulse. Connect this
pin to VCC_5V if not used. Figure 16 shows the SYNC pin
waveform operating at 16 times the switching frequency.
Feedback Loop Compensation
To reduce the number of external components and to simplify
the process of determining compensation components, both
PWM controllers have internally compensated error
amplifiers. To make internal compensation possible several
design measures were taken.
First, the ramp signal applied to the PWM comparator is
proportional to the input voltage provided via the VIN pin.
This keeps the modulator gain constant with variation in the
input voltage. Second, the load current proportional signal is
derived from the voltage drop across the lower MOSFET
during the PWM time interval and is subtracted from the
amplified error signal on the comparator input. This creates
an internal current control loop. The resistor connected to
the ISEN pin sets the gain in the current feedback loop. The
following expression estimates the required value of the
current sense resistor depending on the maximum operating
load current and the value of the MOSFET’s r
DS(ON)
.
Choosing R
CS
to provide 32μA of current to the current
sample and hold circuitry is recommended but values down
to 2μA and up to 100μA can be used.
Due to the current loop feedback, the modulator has a single
pole response with -20dB slope at a frequency determined
by the load.
where R
O
is load resistance and C
O
is load capacitance. For
this type of modulator, a Type 2 compensation circuit is
usually sufficient.
Figure 17 shows a Type 2 amplifier and its response along
with the responses of the current mode modulator and the
converter. The Type 2 amplifier, in addition to the pole at
origin, has a zero-pole pair that causes a flat gain region at
frequencies in between the zero and the pole.
FIGURE 16. SYNC WAVEFORM
R
CS
I
------------------------------------------------
(
)
R
)
(
)
≥
F
PO
O
O
--------------------------------
=
F
Z
2
1
------------------------------
6kHz
=
=
F
P
1
2
------------------------------
600kHz
=
=
ISL6443
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6444 | Dual PWM Controller with DDR Memory Option for Gateway Applications(帶DDR存儲器選項的網關專用雙PWM控制器) |
| ISL6445 | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6445IAZ-TK | 1.4MHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6455 | Triple Output Regulator with Single Synchronous Buck and Dual LDO(帶單同步降壓和雙LDO的三路輸出調節器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6443AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6443A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6443AIRZ | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:熱電冷卻器 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.173"，4.40mm 寬）裸露焊盤 供應商設備封裝:28-TSSOP 裸露焊盤 包裝:管件 產品目錄頁面:1410 (CN2011-ZH PDF) |
| ISL6443AIRZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| ISL6443AIVZ-TK | 功能描述:IC CTRLR SGL/STP DWN PWM 28TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。