- 您現在的位置：買賣IC網 > PDF目錄383148 > ISL6440IA-TK (INTERSIL CORP) 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller PDF資料下載
參數資料
| 型號： | ISL6440IA-TK |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| 中文描述： | 0.4 A DUAL SWITCHING CONTROLLER, 340 kHz SWITCHING FREQ-MAX, PDSO24 |
| 封裝： | 0.150 INCH, PLASTIC, QSOP-24 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 346K |
| 代理商： | ISL6440IA-TK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
8
FN9040.2
October 4, 2005
Pin Descriptions
BOOT2, BOOT1
- These pins power the upper MOSFET
drivers of each PWM converter. Connect this pin to the
junction of the bootstrap capacitor and the cathode of the
bootstrap diode. The anode of the bootstrap diode is
connected to the VCC_5V pin.
UGATE2, UGATE1
- These pins provide the gate drive for
the upper MOSFETs.
PHASE2, PHASE1
- These pins are connected to the junction
of the upper MOSFETs source, output filter inductor and lower
MOSFETs drain.
LGATE2, LGATE1
- These pins provide the gate drive for
the lower MOSFETs.
PGND
- This pin provides the power ground connection for
the lower gate drivers for both PWM1 and PWM2. This pin
should be connected to the sources of the lower MOSFETs
and the (-) terminals of the external input capacitors.
FB2, FB1
- These pins are connected to the feedback
resistor divider and provide the voltage feedback signals for
the respective controller. They set the output voltage of the
converter. In addition, the PGOOD circuit uses these inputs
to monitor the output voltage status.
ISEN2, ISEN1
- These pins are used to monitor the voltage
drop across the lower MOSFET for current loop feedback
and overcurrent protection.
PGOOD
- This is an open drain logic output used to indicate
the status of the output voltages. This pin is pulled low when
either of the two PWM outputs is not within 10% of the
respective nominal voltage.
SGND
- This is the small-signal ground, common to both
controllers, and must be routed separately from the high
current ground (PGND). All voltage levels are measured with
respect to this pin. Connect the additional SGND pins to this
pin.
VIN
- Use this pin to power the device with an external
supply voltage with a range of 5.6V to 24V. For 5V ±10%
operation, connect this pin to VCC5.
VCC5
- This pin is the output of the internal +5V linear
regulator. This output supplies the bias for the IC, the low
side gate drivers, and the external boot circuitry for the high
side gate drivers. The IC may be powered directly from a
single 5V (±10%) supply at this pin. When used as a 5V
supply input, this pin must be externally connected to V
IN
.
The VCC5 pin must be always decoupled to power ground
with a recommended minimum of 4.7
μ
F ceramic capacitor,
placed very close to the pin.
BIAS
- This pin must be connected directly to VCC5.
SS1, SS2
- These pins provide a soft-start function for their
respective PWM controllers. When the chip is enabled, the
regulated 5
μ
A pull-up current source charges the capacitor
connected from this pin to ground. The error amplifier
reference voltage ramps from 0 to 0.8V while the voltage on
the soft-start pin ramps from 0 to 0.8V.
SD1, SD2 -
These pins provide an enable/disable function
for their respective PWM output. The output is enabled when
this pin is floating or pulled HIGH, and disabled when the pin
is pulled LOW.
OCSET2, OCSET1
- A resistor from this pin to ground sets
the overcurrent threshold for the respective PWM.
Functional Description
General Description
The ISL6440 integrates control circuits for two synchronous
buck converters. The two synchronous bucks operate 180
degrees out of phase to substantially reduce the input ripple
and thus reduce the input filter requirements. The chip has
four control lines (SS1, SD1, SS2, and SD2), which provide
independent control for each of the synchronous buck
outputs.
The PWM controllers employ a free-running frequency of
300kHz. The current mode control scheme with an input
voltage feed-forward ramp input to the modulator provides
excellent rejection of input voltage variations and provides
simplified loop compensation.
Internal 5V Linear Regulator (VCC5)
All ISL6440 functions are internally powered from an on-
chip, low dropout, +5V regulator. The maximum regulator
input voltage is 24V. Bypass the regulator’s output (VCC5)
with a 4.7μF capacitor to ground. The dropout voltage for
this LDO is typically 600mV, so when VIN is greater then
5.6V, VCC5V is +5V. The ISL6440 also employs an
undervoltage lockout circuit that disables both regulators
when VCC5 falls below 4.4V.
The internal LDO can source over 60mA to supply the IC,
power the low side gate drivers, charge the external boot
capacitor and supply small external loads. When driving
large FETs, little or no regulator current may be available for
external loads.
For example, a single large FET with 30nC total gate charge
requires 30nC x 300kHz = 9mA. Thus four total FETs would
require 36mA. With 3mA for the internal bias would leave
approximately 20mA for an external +5V supply. Also, at
higher input voltages with larger FETs, the power dissipation
across the internal 5V will increase. Excessive dissipation
across this regulator must be avoided to prevent junction
temperature rise. Larger FETs can be used with 5V ±10%
input applications. The thermal overload protection circuit
will be triggered if the VCC5 output is short circuited.
Connect VCC5 to VIN for 5V ±10% input applications.
ISL6440
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6440IAZ-TK | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6440IAZ | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6440IA | 300kHz Dual, 180 Degree Out-of-Phase, Step-Down PWM Controller |
| ISL6440 | 300kHz Dual, 180° Out-of-Phase, Step-Down PWM Controller(300kHz雙路, 180°異相, 降壓PWM控制器) |
| ISL6441(中文) | 1.4MHz Dual, Out-of-Phase, Step-Down PWM and Single Linear Controller(1.4MHz兩路,異相，降壓型PWM，外加一路線性控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6440IAZ | 功能描述:電流型 PWM 控制器 DUAL PWM CONTRLR+LIN EAR CONTRLR 300KHZ RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6440IAZ-T | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:75 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.3 V ~ 13.5 V 降壓:是 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:0°C ~ 70°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:管件 產品目錄頁面:1051 (CN2011-ZH PDF) 其它名稱:296-2543-5 |
| ISL6440IAZ-T7 | 功能描述:電流型 PWM 控制器 LEAD-FREE DUAL PWM CONTROLLER + LINEAR CONTROLLER, 300KHZ, 1 RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| ISL6440IAZ-TK | 功能描述:IC REG CTRLR BUCK PWM CM 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6441IR | 功能描述:IC CTRLR SGL/STEP DOWN PWM 28QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。