- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6316IRZ-T (INTERSIL CORP) Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6316IRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85 |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220-VJJD-2, QFN-40 |
| 文件頁數： | 19/29頁 |
| 文件大?。?/td> | 838K |
| 代理商： | ISL6316IRZ-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
19
FN9227.0
August 31, 2005
After the DAC voltage reaches the final VID setting, PGOOD
will be set to high with the fixed delay TD3. The typical value
for TD3 is 85μs.
Fault Monitoring and Protection
The ISL6316 actively monitors output voltage and current to
detect fault conditions. Fault monitors trigger protective
measures to prevent damage to a microprocessor load. One
common power good indicator is provided for linking to
external system monitors. The schematic in Figure 12 outlines
the interaction between the fault monitors and the PGOOD
signal.
PGOOD Signal
The PGOOD pin is an open-drain logic output to indicate that
the soft-start period has completed and the output voltage is
within the regulated range. PGOOD is pulled low during
shutdown and releases high after a successful soft-start and a
fixed delay TD5. PGOOD will be pulled low when an
undervoltage or overvoltage condition is detected, or the
controller is disabled by a reset from EN_PWR, EN_VTT,
POR, or VID OFF-code.
Undervoltage Detection
The undervoltage threshold is set at 60% of the VID code.
When the output voltage at VSEN is below the undervoltage
threshold, PGOOD is pulled low.
Overvoltage Protection
Regardless of the VR being enabled or not, the ISL6316
overvoltage protection (OVP) circuit will be active after its
POR. The OVP thresholds are different under different
operation conditions. When VR is not enabled and before the
second soft-start, the OVP threshold is 1.275V. Once the
controller detects valid VID input, the OVP trip point will be
changed to VID plus 175mV.
Two actions are taken by the ISL6316 to protect the
microprocessor load when an overvoltage condition occurs.
At the inception of an overvoltage event, all PWM outputs are
commanded low instantly (less than 20ns) until the voltage at
VDIFF falls below 0.4V. This causes the Intersil drivers to turn
on the lower MOSFETs and pull the output voltage below a
level that might cause damage to the load. The PWM outputs
remain low until VDIFF falls below 0.4V, and then PWM
signals enter a high-impedance state. The Intersil drivers
respond to the high-impedance input by turning off both upper
and lower MOSFETs. If the overvoltage condition reoccurs,
the ISL6316 will again command the lower MOSFETs to turn
on. The ISL6316 will continue to protect the load in this
fashion as long as the overvoltage condition occurs.
Once an overvoltage condition is detected, normal PWM
operation ceases until the ISL6316 is reset. Cycling the
voltage on EN_PWR, EN_VTT or VCC below the POR-falling
threshold will reset the controller. Cycling the VID codes will
not reset the controller.
FIGURE 11. SOFT-START WAVEFORMS
VOUT, 500mV/DIV
EN_VTT
500μs/DIV
TD1
TD2
PGOOD
TD3
FIGURE 12. POWER GOOD AND PROTECTION CIRCUITRY
-
+
VID + 0.175V
VDIFF
-
+
100μA
I
AVG
-
+
DAC
OV
OC
UV
PGOOD
50%
SOFT-START, FAULT
AND CONTROL LOGIC
-
+
OC
I
1
REPEAT FOR
EACH CHANNEL
100μA
Delay
ISL6316
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6401 | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM) |
| ISL6401CB-T | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6401CB | Quadruple 2-Input Exclusive-OR Gates 14-SO -40 to 85 |
| ISL6401CBZ | Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs) |
| ISL6401CR | Quadruple 2-Input Exclusive-OR Gates 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6322CRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6322CRZ-T | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| ISL6322GCRZ | 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
| ISL6322GCRZ-T | 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| ISL6322GIRZ | 功能描述:IC CTRLR PWM BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。