參數資料
型號： ISL6316
廠商： Intersil Corporation
英文描述： Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85
中文描述： 增強4相PWM控制器，用于VR10應用6位VID代碼能夠精確的RDS（ON）或DCR差分電流檢測
文件頁數： 20/29頁
文件大?。?/td> 838K
代理商： ISL6316
20
FN9227.0
August 31, 2005
Overcurrent Protection
ISL6316 has two levels of overcurrent protection. Each phase
is protected from a sustained overcurrent condition on a
delayed basis, while the combined phase currents are
protected on an instantaneous basis.
In instantaneous protection mode, the ISL6316 utilizes the
sensed average current I
AVG
to detect an overcurrent
condition. See the
Channel-Current Balance
section for more
detail on how the average current is measured. The average
current is continually compared with a constant 100
μ
A
reference current as shown in Figure 12. Once the average
current exceeds the reference current, a comparator triggers
the converter to shutdown.
In individual overcurrent protection mode, the ISL6316
continuously compares the current of each channel with the
same 100
μ
A reference current. If any channel current
exceeds the reference current continuously for eight
consecutive cycles, the comparator triggers the converter to
shutdown.
At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state within 20ns
commanding the Intersil MOSFET driver ICs to turn off both
upper and lower MOSFETs. The system remains in this state
a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a soft-
start. If the fault remains, the trip-retry cycles will continue
indefinitely (as shown in Figure 13) until either controller is
disabled or the fault is cleared. Note that the energy delivered
during trip-retry cycling is much less than during full-load
operation, so there is no thermal hazard during this kind of
operation.
Thermal Monitoring (VR_HOT/VR_FAN)
There are two thermal signals to indicate the temperature
status of the voltage regulator: VR_HOT and VR_FAN. Both
VR_FAN and VR_HOT are open-drain outputs, and external
pull-up resistors are required.
VR_FAN signal indicates that the temperature of the voltage
regulator is high and more cooling airflow is needed. VR_HOT
signal can be used to inform the system that the temperature
of the voltage regulator is too high and the CPU should reduce
its power consumption. VR_HOT signal may be tied to the
CPU’s PROCHOT signal.
The diagram of thermal monitoring function block is shown in
Figure 14. One NTC resistor should be placed close to the
power stage of the voltage regulator to sense the operational
temperature, and one pull-up resistor is needed to form the
voltage divider for TM pin. As the temperature of the power
stage increases, the resistance of the NTC will reduce,
resulting in the reduced voltage at TM pin. Figure 15 shows
the TM voltage over the temperature for a typical design with
a recommended 6.8k
NTC (P/N: NTHS0805N02N6801 from
Vishay) and 1k
resistor RTM1. We recommend using those
resistors for the accurate temperature compensation.
There are two comparators with hysteresis to compare the TM
pin voltage to the fixed thresholds for VR_FAN and VR_HOT
signals respectively. VR_FAN signal is set to high when TM
voltage is lower than 33% of Vcc voltage, and is pulled to
GND when TM voltage increases to above 39% of Vcc
voltage. VR_FAN is set to high when TM voltage goes below
28% of Vcc voltage, and is pulled to GND when TM voltage
goes back to above 33% of Vcc voltage. Figure 16 shows the
operation of those signals.
Based on the NTC temperature characteristics and the
desired threshold of VR_HOT signal, the pull-up resistor
RTM1 of TM pin is given by:
R
NTC(T3)
is the NTC resistance at the VR_HOT threshold
temperature T3.
0A
0V
2ms/DIV
OUTPUT CURRENT
FIGURE 13. OVERCURRENT BEHAVIOR IN HICCUP MODE.
F
SW
= 500kHz
OUTPUT VOLTAGE
R
TM1
2.75xR
NTC T3
)
=
(EQ. 16)
ISL6316
相關PDF資料
PDF描述
ISL6316IRZ MINIATURE TOGGLE SWITCH
ISL6316CRZ Enhanced 4-Phase PWM Controller with 6-Bit VID Code Capable of Precision RDS(ON) or DCR Differential Current Sensing for VR10 Application
ISL6316CRZ-T Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85
ISL6316IRZ-T Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85
ISL6401 Synchronizing Current Mode PWM for Subscriber Line Interface Circuits (SLICs)(用戶線接口電路(SLICs)專用同步電流模式PWM)
相關代理商/技術參數
參數描述
ISL6316CRZ 功能描述:軟開關 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR COM RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ISL6316CRZ-T 功能描述:軟開關 PWM 控制器 W/ANNEAL ISL6306 4-PHS VR11 CNTRLRCOM RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ISL6316IRZ 功能描述:軟開關 PWM 控制器 W/ANNEAL 4-PHS VR11 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ISL6316IRZ-T 功能描述:軟開關 PWM 控制器 W/ANNEAL ISL6306 CNTRLR INDUSTRIAL RoHS:否 制造商:Fairchild Semiconductor 輸出端數量: 輸出電流: 開關頻率: 工作電源電壓:30 V 電源電流: 最大工作溫度:+ 105 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel
ISL6322CRZ 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*