- 您現在的位置：買賣IC網 > PDF目錄384525 > ISL6310CRZ (INTERSIL CORP) Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver PDF資料下載
參數資料
| 型號： | ISL6310CRZ |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC32 |
| 封裝： | 5 X 5 MM, ROHS COMPLIANT, PLASTIC, MO-220VHHD-2, QFN-32 |
| 文件頁數： | 8/27頁 |
| 文件大小： | 711K |
| 代理商： | ISL6310CRZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
8
FN9209.2
October 19, 2005
one of four fixed reference voltages; see “Table 1” for
correspondence between REF0 and REF1 inputs and
reference voltage settings.
These pins are internally pulled high, to approximately 1.2V,
by 40
μ
A (typically) internal current sources; the internal pull-
up current decreases to 0 as the REF0 and REF1 voltages
approach the internal pull-up voltage. Both REF0 and REF1
pins are compatible with external pull-up voltages not
exceeding the IC’s bias voltage (VCC).
VSEN and RGND (Pins 8, 7)
VSEN and RGND are inputs to the precision differential
remote-sense amplifier and should be connected to the sense
pins of the remote load.
ICOMP, ISUM, and IREF (Pins 10, 12, 13)
ISUM, IREF, and ICOMP are the DCR current sense
amplifier’s negative input, positive input, and output
respectively. For accurate DCR current sensing, connect a
resistor from each channel’s phase node to ISUM and
connect IREF to the summing point of the output inductors,
roughly VOUT. A parallel R-C feedback circuit connected
between ISUM and ICOMP will then create a voltage from
IREF to ICOMP proportional to the voltage drop across the
inductor DCR. This voltage is referred to as the droop voltage
and is added to the differential remote-sense amplifier’s
output
An optional 0.001-0.01
μ
F ceramic capacitor can be placed
from the IREF pin to the ISUM pin to help reduce common
mode noise that might be introduced by the layout.
DROOP (Pin 11)
This pin enables or disables droop. Tie this pin to the ICOMP
pin to enable droop. To disable droop, tie this pin to the IREF
pin.
VDIFF (Pin 6)
VDIFF is the output of the differential remote-sense amplifier.
The voltage on this pin is equal to the difference between
VSEN and RGND added to the difference between IREF and
ICOMP. VDIFF therefore represents the VOUT voltage plus
the droop voltage.
FB and COMP (Pins 5, 4)
The internal error amplifier’s inverting input and output
respectively. FB is connected to VDIFF through an external
R or R-C network depending on the desired type of
compensation (Type II or III). COMP is tied back to FB
through an external R-C network to compensate the
regulator.
DAC (Pin 32)
The DAC pin is the direct output of the internal DAC. This pin
is connected to REF pin using 1-5k
resistor, This pin can be
left open if an external reference is used.
REF (Pin 1)
The REF input pin is the positive input of the error amplifier.
This pin can be connected to the DAC pin using a resistor
(1-5k
) when the internal DAC voltage is used as the
reference voltage. When an external voltage reference is used,
it must be connected directly to the REF pin, while the DAC pin
is left unconnected. The output voltage will be regulated to the
voltage at the REF pin unless this voltage is greater than the
voltage at the DAC pin. If an external reference is used at this
pin, its magnitude cannot exceed 1.75V.
A capacitor is used between the REF pin and ground to
smooth the DAC voltage during soft-start.
OFST (Pin 2)
The OFST pin provides a means to program a DC current for
generating an offset voltage across the resistor between FB
and VDIFF. The offset current is generated via an external
resistor and precision internal voltage references. The polarity
of the offset is selected by connecting the resistor to GND or
VCC. For no offset, the OFST pin should be left unconnected.
OCSET (Pin 9)
This is the overcurrent set pin. Placing a resistor from OCSET
to ICOMP, allows a 100
μ
A current to flow out of this pin,
producing a voltage reference. Internal circuitry compares the
voltage at OCSET to the voltage at ISUM, and if ISUM ever
exceeds OCSET, the overcurrent protection activates.
ISEN1, ISEN2 (Pins 26, 16)
These pins are used for balancing the channel currents by
sensing the current through each channel’s lower MOSFET
when it is conducting. Connect a resistor between the ISEN1
and ISEN2 pins and their respective phase node. This
resistor sets a current proportional to the current in the lower
MOSFET during its conduction interval.
UGATE1 and UGATE2 (Pins 25, 17)
Connect these pins to the upper MOSFETs’ gates. These
pins are used to control the upper MOSFETs and are
monitored for shoot-through prevention purposes. Maximum
individual channel duty cycle is limited to 66%.
BOOT1 and BOOT2 (Pins 24,18)
These pins provide the bias voltage for the upper MOSFETs’
drives. Connect these pins to appropriately-chosen external
bootstrap capacitors. Internal bootstrap diodes connected to
the PVCC pins provide the necessary bootstrap charge.
PHASE1 and PHASE2 (Pins 23, 19)
Connect these pins to the sources of the upper MOSFETs.
These pins are the return path for the upper MOSFETs’
drives.
LGATE1 and LGATE2 (Pins 27, 14)
These pins are used to control the lower MOSFETs and are
monitored for shoot-through prevention purposes. Connect
these pins to the lower MOSFETs’ gates. Do not use
ISL6310
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6310EVAL1 | Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver |
| ISL6310IRZ | Two-Phase Buck PWM Controller with High Current Intergrated MOSFET Driver |
| ISL6431A | Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications |
| ISL6431ACB | Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications |
| ISL6520A | Adjustable Precision Shunt Regulator 3-SOT-23 -40 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6310CRZ-T | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTRLR W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6310EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6310 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6310IRZ | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6310IRZ-T | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6312ACRZ | 功能描述:IC CTRLR PWM 4PHASE BUCK 48-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |