- 您現在的位置：買賣IC網 > PDF目錄383145 > ISL6308IRZ-T (INTERSIL CORP) Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers PDF資料下載
參數資料
| 型號： | ISL6308IRZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Three-Phase Buck PWM Controller with High Current Integrated MOSFET Drivers |
| 中文描述： | SWITCHING CONTROLLER, 1500 kHz SWITCHING FREQ-MAX, PQCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, PLASTIC, MO-220VJJD-1, QFN-40 |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 765K |
| 代理商： | ISL6308IRZ-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
23
FN9208.2
October 19, 2005
COMPENSATION BREAK FREQUENCY EQUATIONS
Figure 22 shows an asymptotic plot of the DC/DC
converter’s gain vs. frequency. The actual Modulator Gain
has a high gain peak dependent on the quality factor (Q) of
the output filter, which is not shown. Using the above
guidelines should yield a compensation gain similar to the
curve plotted. The open loop error amplifier gain bounds the
compensation gain. Check the compensation gain at F
P2
against the capabilities of the error amplifier. The closed loop
gain, G
CL
, is constructed on the log-log graph of Figure 22
by adding the modulator gain, G
MOD
(in dB), to the feedback
compensation gain, G
FB
(in dB). This is equivalent to
multiplying the modulator transfer function and the
compensation transfer function and then plotting the
resulting gain.
A stable control loop has a gain crossing with close to a
-20dB/decade slope and a phase margin greater than 45
degrees. Include worst case component variations when
determining phase margin. The mathematical model
presented makes a number of approximations and is
generally not accurate at frequencies approaching or
exceeding half the switching frequency. When designing
compensation networks, select target crossover frequencies
in the range of 10% to 30% of the per-channel switching
frequency, F
SW
.
Output Filter Design
The output inductors and the output capacitor bank together
to form a low-pass filter responsible for smoothing the
pulsating voltage at the phase nodes. The output filter also
must provide the transient energy until the regulator can
respond. Because it has a low bandwidth compared to the
switching frequency, the output filter limits the system
transient response. The output capacitors must supply or
sink load current while the current in the output inductors
increases or decreases to meet the demand.
In high-speed converters, the output capacitor bank is
usually the most costly (and often the largest) part of the
circuit. Output filter design begins with minimizing the cost of
this part of the circuit. The critical load parameters in
choosing the output capacitors are the maximum size of the
load step,
I, the load-current slew rate, di/dt, and the
maximum allowable output-voltage deviation under transient
loading,
V
MAX
. Capacitors are characterized according to
their capacitance, ESR, and ESL (equivalent series
inductance).
At the beginning of the load transient, the output capacitors
supply all of the transient current. The output voltage will
initially deviate by an amount approximated by the voltage
drop across the ESL. As the load current increases, the
voltage drop across the ESR increases linearly until the load
current reaches its final value. The capacitors selected must
have sufficiently low ESL and ESR so that the total output-
voltage deviation is less than the allowable maximum.
Neglecting the contribution of inductor current and regulator
response, the output voltage initially deviates by an amount
The filter capacitor must have sufficiently low ESL and ESR
so that
V <
V
MAX
.
Most capacitor solutions rely on a mixture of high frequency
capacitors with relatively low capacitance in combination
with bulk capacitors having high capacitance but limited
high-frequency performance. Minimizing the ESL of the
high-frequency capacitors allows them to support the output
voltage as the current increases. Minimizing the ESR of the
bulk capacitors allows them to supply the increased current
with less output voltage deviation.
The ESR of the bulk capacitors also creates the majority of
the output-voltage ripple. As the bulk capacitors sink and
source the inductor ac ripple current (see
Interleaving
and
Equation 2), a voltage develops across the bulk capacitor
ESR equal to I
C,PP
(ESR). Thus, once the output capacitors
are selected, the maximum allowable ripple voltage,
V
PP(MAX)
, determines the lower limit on the inductance.
Since the capacitors are supplying a decreasing portion of
the load current while the regulator recovers from the
transient, the capacitor voltage becomes slightly depleted.
The output inductors must be capable of assuming the entire
load current before the output voltage decreases more than
V
MAX
. This places an upper limit on inductance.
F
Z1
2
1
------------------------------
=
F
Z2
+
2
π
R
1
R
3
(
)
C
3
-------------------------------------------------
=
F
P1
2
π
R
2
2
C
1
+
C
2
--------------------
--------------------------------------------
=
F
P2
2
π
R
3
C
3
------------------------------
=
0
F
P1
F
Z2
OPEN LOOP E/A GAIN
F
Z1
F
P2
F
LC
F
CE
COMPENSATION GAIN
CLOSED LOOP GAIN
G
FREQUENCY
MODULATOR GAIN
FIGURE 22. ASYMPTOTIC BODE PLOT OF CONVERTER GAIN
20
d
OSC
V
IN
----V
log
20
R1
log
LOG
L
F
0
G
MOD
G
FB
G
CL
V
ESL
(
)
di
dt
----
ESR
(
)
I
+
≈
(EQ. 29)
L
ESR
(
)
V
IN
---F
N V
OUT
–
V
OUT
SW
V
IN
V
PP MAX
)
≥
(EQ. 30)
ISL6308
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6315 | Two-Phase Multiphase Buck PWM Controller with Integrated MOSFET Drivers(帶集成MOSFET驅動器的雙相降壓PWM控制器) |
| ISL6316 | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| ISL6316IRZ | MINIATURE TOGGLE SWITCH |
| ISL6316CRZ | Enhanced 4-Phase PWM Controller with 6-Bit VID Code Capable of Precision RDS(ON) or DCR Differential Current Sensing for VR10 Application |
| ISL6316CRZ-T | Quadruple 2-Input Exclusive-OR Gates 14-PDIP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6308IRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6308IRZ-T WITH GOLD BOND WIRE ONLY - Tape and Reel |
| ISL6310CRZ | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTRLR W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6310CRZ-T | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTRLR W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| ISL6310EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6310 RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓撲結構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
| ISL6310IRZ | 功能描述:電壓模式 PWM 控制器 W/ANNEAL 2-PH PWM CNTROL W/2-DRVRS RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。