- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6298-2CR3 (Intersil Corporation) Li-ion/Li-Polymer Battery Charger PDF資料下載
參數資料
| 型號： | ISL6298-2CR3 |
| 廠商： | Intersil Corporation |
| 英文描述： | Li-ion/Li-Polymer Battery Charger |
| 中文描述： | 鋰聚合物電池充電器 |
| 文件頁數： | 13/17頁 |
| 文件大?。?/td> | 445K |
| 代理商： | ISL6298-2CR3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁
13
FN9173.3
July 20, 2005
Three types of events will result in the FAULT pin to indicate
a logic low signal. The following explains the causes and
consequences.
1. TEMP pin voltage out of window. This is caused by the
ambient temperature being out of the user-set window.
When this fault occurs, the charging is halted until the
temperature returns within the window.
2. TEMP pin voltage higher than the battery removal
threshold. This is caused by the removal of the battery
pack. The charger is disabled when the battery is
removed and enabled when the battery is re-inserted.
3. TIMEOUT fault during trickle mode or CC mode. The
charger is latched when this error occurs. This fault can
only be cleared by cycling the input power or the EN
input.
The STATUS pin indicates a logic low when a charge cycle
starts and indicates a high when the EOC conditions are
met. Once the EOC conditions are met, the STATUS signal
is latched to high until a new charge cycle.
Both the STATUS and the FAULT pin need be pulled up with
external resistors to the 2.8V from the V2P8 pin or the input
voltage. Table 2 summarizes the STATUS and FAULT pins.
Shutdown
The ISL6298 can be shutdown by pulling the EN pin to
ground. When shut down, the charger draws typically less
than 30
μ
A current from the input power and less than 3
μ
A
current from the battery. The 2.8V output at the V2P8 pin is
also turned off. The EN pin needs be driven with an open-
drain or open-collector logic output, so that the EN pin is
floating when the charger is enabled.
Battery Leakage Current
The leakage current from the battery is different when the IC
is enabled and disabled. When the IC is disabled, due to
removing input power or pulling the EN pin to low, the
leakage current is less than 3
μ
A. When the IC is enabled but
not charging (due to a fault condition, the battery removal, or
after termination), the leakage current is caused mainly by
an internal 75k
voltage divider for the output voltage feed-
back. The leakage current is approximately 56
μ
A when the
battery voltage is 4.2V.
Applications Information
Capacitor Selection
Typically any type of capacitors can be used for the input
and the output. A minimum 1
μ
F ceramic capacitor is
recommended to be placed very close to the charger input.
Higher value input decoupling capacitance helps the stable
operation of the charger.
The output capacitor selection is dependent on the
availability of the battery during operation. When the battery
is attached to the charger, the output capacitor can be any
ceramic type with the value higher than 1
μ
F. However, if
there is a chance the charger will be used as a linear
regulator, a 10
μ
F tantalum capacitor is recommended.
The V2P8 pin supplies power to the internal control circuit as
well as external circuits. A good decoupling to this pin is very
important to a reliable operation of the charger. It is
recommended to use a 1
μ
F ceramic capacitor for this pin.
FAULT and STATUS Pull-Up Resistors
Both FAULT and STATUS pins are open-drain outputs that
need an external pull-up resistor. It is recommended that
both pins be pulled up to the input voltage or the 2.8V from
the V2P8 pin, as shown in the Typical Application Circuits. If
the indication pins have to be pulled up to other voltages, the
user needs to examine carefully whether or not the ESD
diodes will form a leakage current path to the battery when
the input power is removed. If the leakage path does exist,
an external transistor is required to break the path.
Figure 24 shows the implementation. If the FAULT pin is
directly pulled up to the VCC voltage (not shown in Figure
24), a current will flow from the VCC to the FAULT pin, then
through the ESD diode to the VIN pin. Any leakage on the
VIN pin, caused by an external or internal current path, will
result in a current path from VCC to ground.
TABLE 2. INDICATION PINS
FAULT STATUS
INDICATION
High
High
Charge completed with no fault (Inhibit) or
Standby
High
Low
Charging in one of the three modes
Low
High
Fault
*Both outputs are pulled up with external resistors.
FIGURE 24. PULL-UP CIRCUIT TO AVOID BATTERY LEAKAGE
CURRENT IN THE ESD DIODES.
FAULT
VIN
VIN
ESD Diode
C
EN
VCC
GND
VIN or
V2P8
STATUS
R
1
Note:
R
is approximately 240k
when EN is floating and is
approximately 140k
when the EN is grounded.
R
LKG
Q
1
ISL6298
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6298-2CR3Z | Quadruple 2-Input Exclusive-OR Gates 14-SOIC -40 to 85 |
| ISL6298-2CR4Z | Li-ion/Li-Polymer Battery Charger |
| ISL6298CR4Z | Quadruple 2-Input Exclusive-OR Gates 14-SSOP -40 to 85 |
| ISL6298-2CR4Z-T | Li-ion/Li-Polymer Battery Charger |
| ISL6298CR4Z-T | Li-ion/Li-Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6298-2CR3Z | 功能描述:IC CHARGER LI-ION 4.2V 3X3 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298-2CR3Z-T | 功能描述:IC CHARGER LI-ION POLYMER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298-2CR4Z | 功能描述:IC CHARGER LI-ION 4.2V 4X4 16QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| ISL6298-2CR4Z-T | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6298CR4Z | 制造商:Intersil Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。