- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6297CR (INTERSIL CORP) Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | ISL6297CR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC16 |
| 封裝： | 4 X 4 MM, PLASTIC, MO-220VGGC, QFN-16 |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 432K |
| 代理商： | ISL6297CR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁
15
FN9215.0
September 27, 2005
Hysteresis Temperature Calculation
Re-arranging EQ. 8, and including the effect of R
S
, gives:
(EQ. 18)
Using the K/(1-K) ratio at the hysteresis threshold, equation
18 provides the NTC thermistor resistance at the threshold.
Continuing the example above, the thermistor values are
found to be 26.2k
and 7.3k
respectively at the low and
high hysteresis temperatures. The corresponding
temperatures are found from Table 3. Cold recovery is about
1.0°C and the hot recovery is about 33.9°C. In other words,
the hysteresis temperatures for the low and high limits are
approximately 6.1°C and 11.0°C, respectively.
Temperature Tolerance Calculation
The temperature accuracy is affected by the accuracy of the
thresholds, R
S
, R
U
, and the NTC thermistor. Using the
maximum ratio K, maximum possible R
U
, and minimum R
S
results in the maximum value of R
T
from EQ. 18, that is:
(EQ. 19)
From the Electrical Specification table, the maximum K at
cold is found to be 0.71. Assuming the resistors have 1%
accuracy, the maximum R
U
is 15.15k
and the minimum R
S
is 40.8
. The resultant maximum R
T
is then found to be
36.3k
and the corresponding temperature is about
negative 6.4°C. Hence the temperature tolerance is 1.3°C.
Similarly, at high temperature, the minimum K is .24, the
minimum R
U
value is 14.85k
and the maximum R
S
is
41.6
. Hence, the highest temperature is 46.0°C and the
tolerance is 1.1°C.
Charging Temperature Range
The selection of R
D
follows the following equation:
(EQ. 20)
where R
T
(@45°C) is the thermistor resistance at 45°C and
the R
T
(@45°C +
T)
is the resistance at some desired
temperature difference above 45°C. Figure 13 shows the
temperature windows before, during, and after charging.
From the example, before and after charging, the
temperature window is -5°C to 45°C with 6°C and 4°C
hysteresis. During charging, the high temperature limit
changes to 45°C +
T. If this limit is exceeded, the charger is
stopped and the temperature has to come back to below
41°C for the charging to be allowed again. The low
temperature limit is also increased. However, the R
D
typically has a much lower resistance than the NTC at low
temperature, therefore, the influence on the temperature
threshold is not as much as at high temperature. Typically,
the low temperature threshold is raised by less than 2°C, as
shown in Figure 13.
2.9V Bias Voltage
A pre-regulator provides a regulated 2.9V on the V2P9 pin,
unless V
IN
drops below 2.9V plus 250mV (typical). Then the
output voltage tracks the input voltage with a 250mV dropout
voltage. The 2.9V output turns off when V
IN
drops below the
VIN (falling) threshold. A minimum 0.1
μ
F X5R ceramic
capacitor is required for decoupling the pre-regulator.
The V2P9 output is used for biasing external circuits. The
maximum loading current on this pin is 30mA. Mainly, the
load current comes from the indication LEDs.
Board Layout Recommendations
The ISL6297 is targeted for space-limited applications. In
order to maximize the current capability, it is very important
that the exposed pad under the package is properly soldered
to the board and is connected to other layers through
thermal vias. More thermal vias and more copper attached to
the exposed pad usually result in better thermal
performance. On the other hand, the number of vias is
limited by the size of the pad. The exposed pads for the 4x4
QFN package are able to have 5 vias. As much copper as
possible should be connected to the exposed pad to
minimize the thermal impedance. Refer to the ISL6297
evaluation board for layout examples.
Related Literature
Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
Technical Brief TB379 “Thermal Characterization of
Packaged Semiconductor Devices”
Technical Brief TB389 “PCB Land Pattern Design and
Surface Mount Guidelines for QFN Packages”
R
T
–
1
K
------------
R
U
R
S
–
×
=
R
TMAX
K
MAX
---–
R
UMAX
R
SMIN
–
×
=
R
D
R
T
@45
o
C
(
)
R
T
@45
o
C
T
+
(
)
–
=
FIGURE 13. BOARD TEMPERATURE MONITORING. WHEN
NOT CHARGING, THE TEMPERATURE WINDOW
IS BETWEEN -5°C AND 45°C. ONCE THE
CHARGER STARTS, THE TEMPERATURE
WINDOW IS ~-3°C TO 45°C+
T
Less than
2°C
45°C+
T
44.7°C
32.0°C
0.6°C
-5.1°C
ISL6297
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6297CRZ | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
| ISL6297CRZ-T | Li-ion/Li Polymer Battery Charger |
| ISL6298-2CR3Z-T | Li-ion/Li-Polymer Battery Charger |
| ISL6298 | Li-ion/Li-Polymer Battery Charger |
| ISL6298-2CR3 | Li-ion/Li-Polymer Battery Charger |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6297CR-T | 功能描述:IC BATT CHRGR 4.2V LI-ION 16-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| ISL6297CRZ | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6297CRZ-T | 功能描述:IC CHARGER LI-ION POLYMER 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| ISL6298 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger |
| ISL6298_06 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li-Polymer Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。