- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6296DH-T (INTERSIL CORP) FlexiHash For Battery Authentication PDF資料下載
參數資料
| 型號： | ISL6296DH-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | FlexiHash For Battery Authentication |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | PLASTIC, EIAJ, SC-74, MO-178AA, SOT-23, 5 PIN |
| 文件頁數： | 7/17頁 |
| 文件大?。?/td> | 384K |
| 代理商： | ISL6296DH-T |
7
FN9201.0
February 1, 2005
It is recommended that device authentication be done once
in a while to maximize its effectiveness. Before a new
challenge code can be accepted by the device, the SESL
register must be re-written again to ensure that the original
seeds are re-loaded from the OTP ROM into the hash
engine prior to performing the next authentication code
calculation. Failure to follow the sequence will result is a bus
error, causing the sBER flag to be set in the STAT register.
SET-UP FOR DEVICE AUTHENTICATION SUPPORT
To configure the host and the ISL6296 to support device
authentication function, the pack manufacturer will need to
select at least 2 sets of 32-bit secret codes. For greater
security, a third set of 32-bit secret may be used. The
FlexiHash engine requires two sets of 32-bit secrets for
use in its hash calculation: the first set to define its hash
function, and the second set to initialize its seed for hash
calculation. These two sets can be selected from the same
secret location. The chosen secret codes are to be kept by
the pack manufacturer and maintained at utmost
confidentiality.
After the secrets have been determined, they are written into
the device’s OTP ROM. After verification that the codes have
been written in correctly, the relevant secrets lock-out bits at
ROM address location 0-00 should be set. Once set, the
lock-out bits can no longer be cleared. Thereafter, read/write
access to the secret information will no longer be possible,
and the secret codes are made available only to the
FlexiHash engine for generation of authentication code
based on a challenge code input from the host.
On the host side, the same secret codes will need to be kept,
and the same FlexiHash engine will have to be
implemented in firmware. Refer to the application note
AN1166 for detailed information of firmware implementation.
It is important that the secret codes be stored scrambled in
the host’s non-volatile memory so that the secret information
cannot be easily revealed by monitoring signal transfer on
the host PCB.
THE HASH ENGINE
The hash engine consists of 4 separate programmable 8-bit
CRC calculators. Two sets of 32-bit secret codes are use by
the hash engine for authentication code generation. The first
set is used to define the CRC polynomial as well as the input
selection for each of the CRC calculators. The second is
used as initial seeds for the CRC calculations. Outputs of the
4 CRC calculators are logically combined to produce the 8-
bit output of the overall FlexiHash engine. Block diagram
of the FlexiHash engine is illustrated in Figure 7. More
detailed description on the hash engine can be found in the
application note AN1166.
FIGURE 5. AUTHENTICATION PROCESS FLOW DIAGRAM
Engine
32-bit Hash Function
32-bit Hash Seed
64-bit Secret
challenge word from host
code
FlexiHash
32-bit pseudo-random
8-bit authentication
FIGURE 6. FLOW CHART FOR AUTHENTICATION PROCESS
START
Wake up ISL6296 using a
regular
break
signal
Select hash function and seed
by writing to SESL register
Send a 32-bit random
challenge to CHLG register
Read the authentication result
from AUTH register, after
waiting for 1 BT
D
END
Calculate the expected
authentication result based on
the same secrets
The two results match
Shut down
the system
YES
NO
ISL6296
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6296EVAL1 | FlexiHash For Battery Authentication |
| ISL6296DHZ-T | FlexiHash For Battery Authentication |
| ISL6297 | Li-ion/Li Polymer Battery Charger |
| ISL6297CR-T | Li-ion/Li Polymer Battery Charger |
| ISL6297CR | Dual Positive-Edge-Triggered D-Type Flip-Flops With Clear and Preset 14-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6296DHZ-T | 功能描述:IC AUTHENTICATION DEVICE SOT23-5 RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:FlexiHash™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6296DHZ-TR5287 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6296DRZ-T | 功能描述:IC AUTHENTICATION BATTERY 8-TDFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:FlexiHash™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| ISL6296EVAL1 | 功能描述:EVALUATION BOARD 1 ISL6296 RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:FlexiHash™ 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6297 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Li-ion/Li Polymer Battery Charger |
發布緊急采購，3分鐘左右您將得到回復。