- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6269A (Intersil Corporation) High-Performance Notebook PWM Controller(高性能筆記本PWM控制器) PDF資料下載
參數資料
| 型號： | ISL6269A |
| 廠商： | Intersil Corporation |
| 英文描述： | High-Performance Notebook PWM Controller(高性能筆記本PWM控制器) |
| 中文描述： | 高性能筆記本PWM控制器（高性能筆記本的PWM控制器） |
| 文件頁數： | 6/14頁 |
| 文件大?。?/td> | 313K |
| 代理商： | ISL6269A |
6
FN9253.2
May 30, 2007
Functional Pin Descriptions
GND (Bottom Pad)
Signal common of the IC. Unless otherwise stated, signals
are referenced to the GND pin, not the PGND pin.
VIN (Pin 1)
The VIN pin measures the converter input voltage which is a
required input to the R
3
PWM modulator. Connect across
the drain of the high-side MOSFET to the GND pin.
VCC (Pin 2)
The VCC pin is the input bias voltage for the IC. Connect
+5V from the VCC pin to the GND pin. Decouple with at least
1μF of a MLCC capacitor from the VCC pin to the GND pin.
FCCM (Pin 3)
The FCCM pin configures the controller to operate in forced-
continuous-conduction-mode (FCCM) or diode-emulation-
mode (DEM.) DEM is disabled when the FCCM pin is pulled
above the rising threshold voltage V
FCCMTHR
, conversely
DEM is enabled when the FCCM pin is pulled below the
falling threshold voltage V
FCCMTHF.
EN (Pin 4)
The EN pin is the on/off switch of the IC. The soft-start
sequence begins when the EN pin is pulled above the rising
threshold voltage V
ENTHR
and VCC is above the power-on
reset (POR) rising threshold voltage
V
VCC_THR
. When the
EN pin is pulled below the falling threshold voltage V
ENTHF
PWM immediately stops.
COMP (Pin 5)
The COMP pin is the output of the control-loop error
amplifier. Compensation components for the control-loop
connect across the COMP and FB pins.
FB (Pin 6)
The FB pin is the inverting input of the control-loop error
amplifier. The converter output voltage regulates to 600mV
from the FB pin to the GND pin. Program the desired output
voltage with a resistor network connected across the VO,
FB, and GND pins. Select the resistor values such that FB to
GND is 600mV when the converter output voltage is at the
programmed regulation value.
FSET (Pin 7)
The FSET pin programs the PWM switching frequency.
Program the desired PWM frequency with a resistor and a
capacitor connected across the FSET and GND pins.
VO (Pin 8)
The VO pin measures the converter output voltage and is
used exclusively as an input to the R
3
PWM modulator.
Connect at the physical location where the best output
voltage regulation is desired.
ISEN (Pin 9)
The ISEN pin programs the threshold of the OCP
overcurrent fault protection. Program the desired OCP
threshold with a resistor connected across the ISEN and
PHASE pins. The OCP threshold is programmed to detect
the peak current of the output inductor. The peak current is
the sum of the DC and AC components of the inductor
current.
PGND (Pin 10)
The PGND pin conducts the turn-off transient current
through the LG gate driver. The PGND pin must be
connected to complete the pulldown circuit of the LG gate
driver. The PGND pin should be connected to the source of
the low-side MOSFET through a low impedance path,
preferably in parallel with the trace connecting the LG pin to
the gate of the low-side MOSFET. The adaptive shoot-
through protection circuit, measures the low-side MOSFET
gate-source voltage from the LG pin to the PGND pin.
PROTECTION
ISEN OCP Threshold
I
OC
ISEN sourcing, T
A
= -10°C to +100°C
ISEN sourcing
19
26
33
μ
A
17
26
33
μ
A
ISEN Short-Circuit Threshold
I
SC
V
UV
V
OVR
V
OVF
T
OTR
T
OTHYS
ISEN sourcing
-
50
-
μ
A
UVP Threshold
81
84
87
%
OVP Rising Threshold
113
116
119
%
OVP Falling Threshold
100
103
106
%
OTP Rising Threshold (Note 3)
-
150
-
°C
OTP Hysteresis (Note 3)
-
25
-
°C
NOTE:
3. Guaranteed by characterization.
Electrical Specifications
These specifications apply for V
IN
= 15V, T
A
= -40°C to +100°C, unless otherwise stated.
All typical specifications T
A
= +25°C, VCC = 5V, PVCC = 5V, VIN = 15V
(Continued)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX
UNIT
ISL6269A
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6271ACRZ | Integrated XScale Regulator |
| ISL6271ACRZ-T | Integrated XScale Regulator |
| ISL6271A | Integrated XScale Regulator |
| ISL6271ACR | Integrated XScale Regulator |
| ISL6271ACR-T | Integrated XScale Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6269ACRZ | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-T | 功能描述:IC REG CTRLR BUCK PWM 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:275kHz 占空比:50% 電源電壓:18 V ~ 110 V 降壓:無 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:是 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) |
| ISL6269ACRZ-TR5453 | 制造商:Intersil Corporation 功能描述:STD. ISL6269ACRZ-T WITH GOLD BOND WIRE ONLY, T&R - Tape and Reel |
| ISL6269AEVAL2 | 制造商:Intersil Corporation 功能描述:ISL6269A EVALUATION BOARD 2 - Bulk |
| ISL6269AEVAL2Z | 功能描述:EVALUATION BOARD FOR ISL6269A RoHS:是 類別:編程器，開發系統 >> 評估板 - DC/DC 與 AC/DC（離線）SMPS 系列:Robust Ripple Regulator™ (R³) 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:True Shutdown™ 主要目的:DC/DC，步升 輸出及類型:1，非隔離 功率 - 輸出:- 輸出電壓:- 電流 - 輸出:1A 輸入電壓:2.5 V ~ 5.5 V 穩壓器拓?fù)浣Y(jié)構:升壓 頻率 - 開關:3MHz 板類型:完全填充 已供物品:板 已用 IC / 零件:MAX8969 |
發布緊急采購，3分鐘左右您將得到回復。