- 您現在的位置：買賣IC網 > PDF目錄383140 > ISL6140IB (INTERSIL CORP) Negative Voltage Hot Plug Controller PDF資料下載
參數資料
| 型號： | ISL6140IB |
| 廠商： | INTERSIL CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Negative Voltage Hot Plug Controller |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8 |
| 封裝： | MS-012-AA, PLASTIC, SOIC-8 |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 511K |
| 代理商： | ISL6140IB |
8
Applications: Over-Current
Physical layout of R1 SENSE resistor
is critical to avoid
the possibility of false overcurrent occurrences. Since it is in
the main input-to-output path, the traces should be wide
enough to support both the normal current, and up to the
over-current trip point. Ideally trace routing between the R1
resistor and the ISL6140/ISL6150 (pin 4 (VEE) and pin 5
(SENSE) is direct and as short as possible with zero current
in the sense lines. (See Figure 5).
There is a short filter (3
μ
s nominal) on the comparator; current
spikes shorter than this will be ignored. Any longer pulse will
shut down the output, requiring the user to either power down
the system (below the UV voltage), or pull the UV pin below its
trip point (usually with an external transistor).
If current pulses longer than the 3
μ
s are expected, and need
to be filtered, then an additional resistor and capacitor can
be added. As shown in Figure 29, R7 and C3 act as a low-
pass filter such that the voltage on the SENSE pin won’t rise
as fast, effectively delaying the shut-down. Since the
ISL6140/ISL6150 has essentially zero current on the
SENSE pin, there is no voltage drop or error associated with
the extra resistor. R7 is recommended to be small, 100
is a
good value.
The delay time is approximated by the added RC time
constant, modified by a factor relative to the trip point.
t = - R * C * ln [1 - (V(t) - V(t
0
)) / (V
i
- V(t
0
))]
where V(t) is the trip voltage (nominally 50mV); V(t
0
) is the
nominal voltage drop across the sense resistor before the
over-current condition; V
i
is the voltage drop across the
sense resistor while the over-current is applied.
For example: a system has a normal 1A current load, and a
20m
sense resistor, for a 2.5A over-current. It needs to
filter out a 50
μ
s current pulse at 5A. So,
V(t) = 50mV (from spec)
V(t
0
) = 20mV (V = IR = 1A * 20m
)
V
i
= 100mV (V = IR = 5A * 20m
)
If R7 = 100
, then C3 is around 1
μ
F.
Note that the FET must be rated to handle the higher current
for the longer time, since the IC is not doing current limiting;
the RC is just delaying the over-current shutdown.
Applications: OV and UV
The UV and OV input pins are high impedance, so the value
of the external resistor divider is not critical with respect to
input current. Therefore, the next consideration is total
current; the resistors will always draw current, equal to the
supply voltage divided by the total of R4+R5+R6; so the
values should be chosen high enough to get an acceptable
current. However, to the extent that the noise on the power
supply can be transmitted to the pins, the resistor values
might be chosen to be lower. A filter capacitor from UV to
VEE or OV to UV is a possibility, if certain transients need to
be filtered. (Note that even some transients which will
momentarily shut off the gate might recover fast enough
such that the gate or the output current does not even see
the interruption).
Finally, take into account whether the resistor values are
readily available, or need to be custom ordered. Tolerances
of 1% are recommended for accuracy. Note that for a typical
48V system (with a 36V to 72V range), the 36V or 72V is
being divided down to 1.223V, a significant scaling factor.
For UV, the ratio is roughly 30 times; every 3mV change on
the UV pin represents roughly 0.1V change of power supply
voltage. Conversely, an error of 3mV (due to the resistors,
for example) results in an error of 0.1V for the supply trip
point. The OV ratio is around 60. So the accuracy of the
resistors comes into play.
The hysteresis of the comparators (20mV nominal) is also
multiplied by the scale factor of 30 for the UV pin
(30 * 20mV = 0.6V of hysteresis at the power supply) and 60
for the OV pin (60 * 20mV = 1.2V of hysteresis at the power
supply).
With the three resistors, the UV equation is based on the
simple resistor divider:
1.223 = V
UV
* (R5 + R6)/(R4 + R5 + R6) or
V
UV
= 1.223 (R4 + R5 + R6)/(R5 + R6)
Similarly, for OV:
1.223 = V
OV
* (R6)/(R4 + R5 + R6) or
V
OV
= 1.223 (R4 + R5 + R6)/(R6)
Note that there are two equations, but 3 unknowns. Because
of the scale factor, R4 has to be much bigger than the other
two; chose its value first, to set the current (for example,
50V/500k
draws 100
μ
A), and then the other two will be in
the 10k
range. Solve the two equations for two unknowns.
Note that some iteration may be necessary to select values
that meet the requirement, and are also readily available
standard values.
CORRECT
TO SENSE
AND V
EE
CURRENT
SENSE RESISTOR
INCORRECT
FIGURE 5. SENSE RESISTOR
ISL6140, ISL6150
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6150 | Octal D-Type Transparent Latches With 3-State Outputs 20-SSOP -40 to 85 |
| ISL6150CB | Octal D-Type Transparent Latches With 3-State Outputs 20-SSOP -40 to 85 |
| ISL6150CB-T | Octal D-Type Transparent Latches With 3-State Outputs 20-SSOP -40 to 85 |
| ISL6150CBZ | Octal D-Type Transparent Latches With 3-State Outputs 20-SOIC -40 to 85 |
| ISL6140IBZ | Negative Voltage Hot Plug Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6140IB-T | 功能描述:IC CONTROLLER HOT PLUG 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| ISL6140IBZ | 功能描述:IC CONTROLLER HOT PLUG 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| ISL6140IBZ-T | 功能描述:IC CTRLR HOT PLUG NEG VOLT 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| ISL6141 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Negative Voltage Hot Plug Controller |
| ISL6141CB | 功能描述:IC CONTROLLER HOT PLUG 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。