- 您現在的位置：買賣IC網 > PDF目錄384524 > ISL6125EVAL1 (Intersil Corporation) Power Sequencing Controllers PDF資料下載
參數資料
| 型號： | ISL6125EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Power Sequencing Controllers |
| 中文描述： | 電源順序控制器 |
| 文件頁數： | 10/21頁 |
| 文件大小： | 488K |
| 代理商： | ISL6125EVAL1 |
10
FN9005.8
February 5, 2007
Using the ISL612XSEQEVAL1 Platform
The
ISL612XSEQEVAL1
platform is the primary evaluation
board for this family. The board has two complete, separate
and electrically identical circuits. See Figure 15 for its
schematic and photograph. Additionally, there is an ISL6125
specific eval platform,
ISL6125EVAL1
, due to its unique
open drain outputs for ease of evaluation. See Figure 16 for
its schematic and photograph.
In the top right hand corner of the board is a SMD layout with
a
ISL6123
illustrating the full functionality and small
implementation size for an application having the highest
component count.
The majority of the board is given over to a socket and
discrete through-hole components circuit for ease of
evaluation flexibility through IC variant swapping and
modification of UVLO levels and sequencing order by
passive component substitution.
The board is shipped with the
ISL6123
installed in both
locations and with two each of the other released variant
types loose packed. As this sequencer family has a common
function pinout there are no major modifications to the board
necessary to evaluate the other ICs.
To the left, right and above the socket are four test point
strips (TP1, TP2, TP3, TP4). These give access to the
labeled IC I/O pins during evaluation. Remember that
significant current or capacitive loading of particular I/O pins
will affect functionality and performance.
Attention to orientation and placement of variant ICs in the
socket must be paid to prevent IC damage or faulty
evaluation.
The default configuration of the
ISL612XSEQEVAL1
circuitries was built around the following design
assumptions:
1. Using the
ISL6123IR
or
ISL6124IR
2. The four supplies being sequenced are 5V (IN_A), 3.3V
(IN_B), 2.5V (IN_C) and 1.5V (IN_D), the UVLO levels
are ~80% of nominal voltages. Resistors chosen such
that the total resistance of each divider is ~10k using
standard value resistors to approximate 80% of
nominal = 0.63V on UVLO input.
Resistor choice is such that I x R2 = 0.633V at the desired
UV (undervoltage) level as the monitored voltage
decreases. Total resistance in the divider is a factor for
the designer to consider for accuracy of UV level and
efficiency vs electrical noise immunity trade-offs.
3. The desired order turn-on sequence is first both 5V and
3.3V supplies together and then the 2.5V supply about
75ms later and lastly the 1.5V supply about 45ms later.
4. The desired turn-off sequence is first both 1.5V and 3.3V
supplies at the same time then the 2.5V supply about
50ms later and lastly the 5V supply about 72ms after that.
All scope shots are taken from ISL612XSEQEVAL1 board.
Figures 7 and 8 illustrate the desired turn-on and turn-off
sequences respectively. The sequencing order and delay
between voltages sequencing is set by external capacitance
values, so other than illustrated can be accomplished.
FIGURE 6. SYSRST# LOW TO OUTPUT LATCH OFF
Typical Performance Curves
(Continued)
1
μ
s/DIV
5VOUT
GATE
SYSRST#
2V/DIV
3.3VOUT
Vmonitored
R1
R2
UVLO
Vmon/0.633mV = R1+R2/R2
when Vmon = desired UV level as
Vmon decreases.
For example, a 5V supply with a
desired UV level at 4V would mean
R1+R2/R2 = 6.319. Ideally, any R1
and R2 combination that met this ratio
would work, but with only standard
value resistors available, small
deviations will occur.
ISL6123, ISL6124, ISL6125, ISL6126, ISL6127, ISL6128, ISL6130
相關PDF資料 |
PDF描述 |
|---|---|
| ISL6130 | Power Sequencing Controllers |
| ISL6130IRZA | Power Sequencing Controllers |
| ISL6205 | High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6205CB-T | High Voltage Synchronous Rectified Buck MOSFET Driver |
| ISL6205CB | Octal D-Type Transparent Latches With 3-State Outputs 20-TSSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL6125EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL6125 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL6125IR | 功能描述:IC SEQUENCER POWER 4-CH 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6125IRS2604 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: |
| ISL6125IR-T | 功能描述:IC CTRLR PWR SEQUENCE 4CH 24-QFN RoHS:否 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
| ISL6125IRZA | 功能描述:IC POWER SUPPLY SEQUENCER 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源控制器，監視器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 應用:多相控制器 輸入電壓:- 電源電壓:9 V ~ 14 V 電流 - 電源:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:40-WFQFN 裸露焊盤 供應商設備封裝:40-TQFN-EP（5x5） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。