- 您現在的位置：買賣IC網 > PDF目錄383137 > ISL59830IA-T13 (INTERSIL CORP) True Single Supply Video Driver PDF資料下載
參數資料
| 型號： | ISL59830IA-T13 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | True Single Supply Video Driver |
| 中文描述： | 3 CHANNEL, VIDEO AMPLIFIER, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, QSOP-16 |
| 文件頁數： | 12/14頁 |
| 文件大?。?/td> | 416K |
| 代理商： | ISL59830IA-T13 |
12
FN7489.2
August 15, 2005
The Charge Pump
The ISL59830 charge pump provides a bottom rail up to
1.65V below ground while operating on a 0V to 3.3V power
supply. The charge pump is internally regulated to one-half
the potential of the positive supply. This internal multi-phase
charge pump is driven by a 160MHz differential ring
oscillator driving a series of inverters and charge storage
circuitry. Each series inverter charges and places parallel
adjoining charge circuitry slightly out of phase with the
immediately preceding block. The overall effect is sequential
discharge and generation of a very low ripple of about 10mV
that is applied to the amplifiers providing a negative rail of up
to -1.65V.
FIGURE 28. CHARGE PUMP OSCILLATION
The system operates at sufficiently high frequencies that any
related charge pump noise is far beyond standard video
bandwidth requirements. Still, appropriate bypassing
discipline must be observed, and all pins related to either the
power supply or the charge pump must be properly
bypassed. See "Power Supply Bypassing and Printed Circuit
Board Layout" in this section.
The V
REF
Pin
Applying a voltage to the V
REF
pin simply places that
voltage on what would usually be the ground side of the gain
resistor of the amplifier, resulting in a DC-level shift of the
output signal. Applying 100mV to the Vref pin would apply a
100mV DC level shift to an incoming signal. The charge
pump providing sufficient bottom room to accommodate the
shifted signal.
See Block Diagram on page 8.
The V
EE
Pin
The V
EE
pin is the output pin for the charge pump. A
voltmeter applied to this pin will display the output of the
charge pump. This pin does not affect the functionality of the
part. One may use this pin as an additional voltage source.
Keep in mind that the output of this pin is generated by the
internal charge pump and a fully regulated supply that must
be properly bypassed. We recommend a 0.1μF ceramic
capacitor placed as close to the pin and connected to the
ground plane of the board.
Input, Output, and Supply Voltage Range
The ISL59830 is designed to operate with a single supply
voltage range of from 0V to 3.3V. The need for a split supply
has been eliminated with the incorporation of a charge pump
capable of generating a bottom rail as much as 1.6V below
ground, for a 4.9V range on a single 3.3V supply. This
performance is ideal for NTSC video with its negative-going
sync pulses.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency and phase response as DC levels are changed at
the output. This is especially difficult when driving a standard
video load of 150
because of the change in output current
with changing DC levels. Special circuitry has been
incorporated into the ISL59830 for the reduction of output
impedance variation with the current output. This results in
outstanding differential gain and differential phase
specifications of 0.06% and 0.1°, while driving 150
at a
gain of +2. Driving higher impedance loads would result in
similar or better differential gain and differential phase
performance.
NTSC
The ISL59830, generating a negative rail internally, is ideally
suited for NTSC video with its accompanying negative-going
sync signals; easily handled by the ISL59830 without the
need of an additional supply as the ISL59830 generates a
negative rail with an internal charge pump referenced at
negative 1/2 the positive supply.
YPbPr
YPbPr signals originating from a DVD player requiring three
channels of very tightly-controlled amplifier gain accuracy
present no difficulty for the ISL59830. Specifically, this
standard encodes sync on the Y channel and it is a negative-
going signal; easily handled by the ISL59830 without the
need of an additional supply as the ISL59830 generates a
negative rail placed at negative 1/2 the positive supply.
Additionally, the Pb and Pr are bipolar analog signals and
the video signals are negative-going; and again easily
handled by the ISL59830.
Driving Capacitive Loads and Cables
The ISL59830, internally-compensated to drive 75
cables,
will drive 10pF loads in parallel with 1k
with less than 5dB
of peaking. If less peaking is required, a small series resistor,
usually between 5
to 50
, can be placed in series with the
output. This will reduce peaking at the expense of a slight
closed loop gain reduction. When used as a cable driver,
double termination is always recommended for reflection-
free performance. For those applications, a back-termination
series resistor at the amplifier's output will isolate the
V
TIME (20ns/DIV)
ISL59830
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59830IA | True Single Supply Video Driver |
| ISL59830IAZ | True Single Supply Video Driver |
| ISL59830 | True Single Supply Video Driver(真正的單電源視頻驅動器) |
| ISL59831 | Single Supply Video Driver with Reconstruction Filter and Charge Pump |
| ISL59831IRTZ-T7 | Single Supply Video Driver with Reconstruction Filter and Charge Pump |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59830IA-T7 | 功能描述:IC VID DRIVER TRUE SGL 16-QSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59830IAZ | 功能描述:IC DRIVER VIDEO SGL 3.3V 16QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59830IAZ-EVAL | 制造商:Intersil Corporation 功能描述:TRUE SGL SUPPLY VID DRVR - Bulk 制造商:Intersil Corporation 功能描述:BOARD EVAL FOR ISL59830 制造商:Intersil 功能描述:ISL90843W LW NOISE LW PWR I2C BUS 256 |
| ISL59830IAZ-T13 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| ISL59830IAZ-T7 | 功能描述:IC VIDEO DRIVER TRUE SGL 16-QSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。