- 您現在的位置：買賣IC網 > PDF目錄383137 > ISL59441IAZ-T13 (INTERSIL CORP) 900MHz Multiplexing Amplifier PDF資料下載
參數資料
| 型號： | ISL59441IAZ-T13 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | 900MHz Multiplexing Amplifier |
| 中文描述： | 4-CHANNEL, VIDEO MULTIPLEXER, PDSO16 |
| 封裝： | LEAD FREE, 0.150 INCH, QSOP-16 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 571K |
| 代理商： | ISL59441IAZ-T13 |
11
FN6163.2
September 21, 2005
PC Board Layout
The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The following are
recommendations to achieve optimum high frequency
performance from your PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended.
Minimize signal trace lengths. Trace inductance and
capacitance can easily limit circuit performance. Avoid
sharp corners, use rounded corners when possible. Vias
in the signal lines add inductance at high frequency and
should be avoided. PCB traces greater than 1" begin to
exhibit transmission line characteristics with signal rise/fall
times of 1ns or less. High frequency performance may be
degraded for traces greater than one inch, unless strip
lines are used.
Match channel-channel analog I/O trace lengths and
layout symmetry. This will minimize propagation delay
mismatches.
Maximize use of AC de-coupled PCB layers. All signal I/O
lines should be routed over continuous ground planes (i.e.
no split planes or PCB gaps under these lines). Avoid vias
in the signal I/O lines.
Use proper value and location of termination resistors.
Termination resistors should be as close to the device as
possible.
When testing use good quality connectors and cables,
matching cable types and keeping cable lengths to a
minimum.
Minimum of 2 power supply de-coupling capacitors are
recommended (1000pF, 0.01μF) as close to the device as
possible. Avoid vias between the cap and the device
because vias add unwanted inductance. Larger caps can
be farther away. When vias are required in a layout, they
should be routed as far away from the device as possible.
The NIC pins are placed on both sides of the input pins.
These pins are not internally connected to the die. It is
recommended these pins be tied to ground to minimize
crosstalk.
ISL59441
相關PDF資料 |
PDF描述 |
|---|---|
| ISL59441IAZ-T7 | 900MHz Multiplexing Amplifier |
| ISL59442IB-T13 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB-T7 | 1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB | 1GHz, 4 x 1 Multiplexing Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL59441IAZ-T7 | 制造商:Intersil Corporation 功能描述:ANLG MUX/AMP SGL 4:1 5.5V 16QSOP - Tape and Reel 制造商:Intersil 功能描述:ISL8120 EVALRD 3 RHS CMPL -1 CON |
| ISL59442 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1GHz, 4 x 1 Multiplexing Amplifier |
| ISL59442IB | 功能描述:IC CROSSPOINT SW 1GHZ 4X1 14SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| ISL59442IB-T13 | 功能描述:IC CROSSPOINT SW 1GHZ 4X1 14SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。