- 您現在的位置：買賣IC網 > PDF目錄1927 > ISL54062IRUZ-T (Intersil)IC SWITCH SPDT DUAL 10TQFN PDF資料下載
參數資料
| 型號： | ISL54062IRUZ-T |
| 廠商： | Intersil |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH SPDT DUAL 10TQFN |
| 標準包裝： | 3,000 |
| 功能： | 開關 |
| 電路： | 2 x SPDT |
| 導通狀態電阻： | 550 毫歐 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 1.8 V ~ 6.5 V |
| 電流 - 電源： | 20nA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-UFQFN |
| 供應商設備封裝： | 10-UTQFN（1.8x1.40） |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
10
FN6581.1
November 3, 2009
The minimum recommended supply voltage is 1.8V. It is
important to note that the input signal range, switching times,
and ON-resistance degrade at lower supply voltages. Refer
to the “Electrical Specifications” tables, beginning on page 3,
and “Typical Performance Curves”, beginning on page 11,
for details.
V+ and GND also power the internal logic and level shifters.
The level shifters convert the input logic levels to V+ and
GND signals levels to drive the analog switch gate terminals.
A high frequency decoupling capacitor placed as close to the
V+ and GND pin as possible is recommended for proper
operation of the switch. A value of 0.1F is highly
recommended.
Negative Signal Swing Capability
The ISL54062 contains circuitry that allows the analog
switch signal to swing below ground. The device has an
analog signal range of 6.5V below V+ up to the V+ rail (see
example, if V+ = 5V, then the analog input signal range is
from -1.5V to +5V. If V+ = 2.7V then the range is from -3.8V
to +2.7V.
Click and Pop Operation
The ISL54062 contains circuitry that prevents audible click
and pop noises that may occur when audio sources are
powered on or off. Single supply audio sources are biased at
a DC offset that can generate transients during power on/off.
A DC blocking capacitor is needed to remove the DC bias at
the speaker load. For 32
Ω headphones, a 220F capacitor is
typically used to preserve the audio bandwidth. The power
on/off transients are AC coupled by the 220F capacitor to
the speaker load causing a click and pop noise.
The ISL54062 has shunt switches on the NO and NC pins to
eliminate click and pop transients (see Figure 10). These
switches are driven complimentary to the main switch. When
NC is connected to COM, the shunt switch is active on the
NO pin (and vice versa). The shunt switches connect an
impedance (140
Ω typical, see Figure 24) from the NO/NC
pin to ground to discharge any transients that may appear on
the NO or NC pins.
When a DC bias becomes active at the source, the NO and
NC terminals will also have a DC offset due to capacitor
dv/dt principle. The DC offset will be discharged through the
shunt impedance on the NO and NC terminals instead of the
speaker, eliminating click and pop noise.
*Under high impedance loads such as the input impedance
of pre-amplifiers (20k
Ω), the COM terminal voltage may rise
due to small leakage currents charging the COM
capacitance. This is not seen when low impedance loads
such as headphones (32
Ω) are used because the small
leakage currents does not result in significant potential drop
across the load. If the user desires to reduce the voltage
build up on the COM pin, a 1k
Ω resistor to ground may be
placed on the COM pin. This impedance is small enough to
reduce the voltage build up significantly while not increasing
the power dissipation dramatically. Current consumption
considerations will need to be taken for driving a smaller
load impedance under this scenario.
Click and Pop Elimination with INx Pin
Audio click and pop elimination can be driven with the Input
Select (INx) pin. When INx = 0, the NOx terminals are
connected to the shunt impedance. When INx = 1, the NCx
terminals are connected to the shunt impedance. In this
situation, only one of the source transient voltages will be
shunted to ground, depending on the Input Select state. The
Input Select pin should be driven 200ms after any source
transients occurs to prevent audible transients at the
speaker load.
Logic-Level Thresholds
This switch family is 1.8V CMOS compatible (0.45V VOLMAX
and 1.35V VOHMIN) over a supply range of 1.8V to 3.3V
is still below the 1.8V CMOS guaranteed low output
maximum level of 0.45V, but noise margin is reduced to
approximately 50mV. At 3.3V the VIH level is 1.4V minimum.
While this is above the 1.8V CMOS guaranteed high output
minimum of 1.35V, under most operating conditions the
switch will recognize this as a valid logic high.
The digital input stages draw supply current whenever the
digital input voltage is not at one of the supply rails. Driving
the digital input signals from GND to V+ with a fast transition
time minimizes power dissipation. The ISL54062 has been
designed to minimize the supply current whenever the digital
input voltage is not driven to the supply rails (0V to V+). For
example, driving the device with 2.85V logic high while
operating with a 4.2V supply the device draws only 1A of
current.
IN
COM
RL
220F
32
Ω
NO
NC
V+
GND
C
AUDIO
SOURCE A
220F
RSH
AUDIO
SOURCE B
RSH
ISL54062
FIGURE 10. CLICK AND POP OPERATION
ISL54062
相關PDF資料 |
PDF描述 |
|---|---|
| ISL54064IRUZ-T | IC SWITCH SPDT DUAL 10TQFN |
| ISL54065IRUZ-T | IC SWITCH DUAL SPDT 12UTQFN |
| ISL54066IRUZ-T | IC SWITCH SPDT DUAL 10TQFN |
| ISL54100ACQZ | IC TMDS REGENERATOR MUX 128-MQFP |
| ISL54101CQZ | IC RGEN MUX TMDS 1:1 128-MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL54063 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:1.8V to +6.5V, Sub-ohm, Dual SPST |
| ISL54063_0911 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Negative Signal Swing, Sub-ohm, Dual SPST |
| ISL54063EVAL1Z | 功能描述:EVALUATION BOARD FOR ISL54063 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL54063IRTZ | 功能描述:IC SWITCH SPDT DUAL 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
| ISL54063IRTZ-T | 功能描述:IC SWITCH SPDT DUAL 10TDFN RoHS:是 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:36 系列:- 功能:多路復用器 電路:2 x 4:1 導通狀態電阻:75 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:- 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:20-SOIC W 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。