4
FN6022.6
November 17, 2004
Absolute Maximum Ratings
Thermal Information
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to15V
Input Voltages
IN (Note 3). . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 3) . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 3) . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . .
30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . .
40mA
ESD Rating (Per MIL-STD-883 Method 3015). . . . . . . . . . . . . .>2kV
Operating Conditions
Temperature Range
ISL512XCX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
ISL512XIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C
Thermal Resistance (Typical, Note 4)
6 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . .
8 Ld SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature (Plastic Package). . . . . . . . 150°C
Moisture Sensitivity (See Technical Brief TB363)
All Other Packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 1
8 Ld SOT-23 Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . Level 2
Maximum Storage Temperature Range . . . . . . . . . . . . . -65°C to 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300°C
(Lead Tips Only)
θ
JA
(°C/W)
230
215
170
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
2. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
3.
θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications - 5V Supply
Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 5),
Unless Otherwise Specified
PARAMETER
TEST CONDITIONS
TEMP
(°C)
(NOTE 6)
MIN
TYP
(NOTE 6)
MAX
UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full
0
-
V+
V
ON Resistance, R
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V,
(See Figure 5)
25
-
19
30
Full
-
23
40
R
ON
Matching Between Channels,
R
ON
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V
25
-
0.8
2
Full
-
1
4
R
ON
Flatness, R
FLAT(ON)
V+ = 5V, I
COM
= 1.0mA, V
NO
or V
NC
= 1V, 2V, 3V
Full
-
7
8
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V,
(Note 7)
25
-0.1
0.01
0.1
nA
Full
-5
-
5
nA
COM OFF Leakage Current,
I
COM(OFF)
V+ = 5.5V, V
COM
= 4.5V, 1V, V
NO
or V
NC
= 1V, 4.5V,
(Note 7)
25
-0.1
-
0.1
nA
Full
-5
-
5
nA
COM ON Leakage Current,
I
COM(ON)
V
+
= 5.5V, V
COM
= 1V, 4.5V, or V
NO
or V
NC
= 1V, 4.5V,
or Floating, (Note 7)
25
-0.2
-
0.2
nA
Full
-10
-
10
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V
NO
or V
NC
= 3V, R
L
=1k
, C
L
= 35pF, V
IN
= 0 to 3V,
(See Figure 1)
25
-
28
75
ns
Full
-
40
150
ns
Turn-OFF Time, t
OFF
V
NO
or V
NC
= 3V, R
L
=1k
, C
L
= 35pF, V
IN
= 0 to 3V,
(See Figure 1)
25
-
20
50
ns
Full
-
30
100
ns
Break-Before-Make Time Delay
(ISL5122, ISL5123), t
D
R
L
= 300
, C
L
= 35pF, V
NO
= V
NC
= 3V, V
IN
= 0 to 3V,
(See Figure 3)
Full
3
10
-
ns
Charge Injection, Q
C
L
= 1.0nF, V
G
= 0V, R
G
= 0
, (See Figure 2)
25
-
3
5
pC
OFF Isolation
R
L
= 50
, C
L
= 5pF, f = 1MHz, (See Figure 4)
25
-
76
-
dB
Crosstalk (Channel-to-Channel)
R
L
= 50
, C
L
= 5pF, f = 1MHz, (See Figure 6)
25
-
-105
-
dB
ISL5120, ISL5121, ISL5122, ISL5123