- 您現在的位置：買賣IC網 > PDF目錄9864 > ISL4270EIRZ (Intersil)IC 3DRVR/3RCVR RS232 3V 32-QFN PDF資料下載
參數資料
| 型號： | ISL4270EIRZ |
| 廠商： | Intersil |
| 文件頁數： | 13/13頁 |
| 文件大小： | 0K |
| 描述： | IC 3DRVR/3RCVR RS232 3V 32-QFN |
| 標準包裝： | 60 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 3/3 |
| 規程： | RS232 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 管件 |
9
FN6041.2
June 16, 2010
“INVALID DRIVING FORCEON AND FORCEOFF” section
of Table 2 for an operational summary. This operational
mode is perfect for handheld devices that communicate with
another computer via a detachable cable. Detaching the
cable allows the internal receiver pull-down resistors to pull
the inputs to GND (an invalid RS-232 level), causing the
30
μs timer to time-out and drive the IC into powerdown.
Reconnecting the cable restores valid levels, causing the IC
to power back up.
Hybrid Automatic Powerdown Options
For devices which communicate only through a detachable
cable, connecting INVALID to FORCEOFF (with
FORCEON = 0) may be a desirable configuration. While the
cable is attached INVALID and FORCEOFF remain high, so
the enhanced automatic powerdown logic powers down the
RS-232 device whenever there is 30 seconds of inactivity on
the receiver and transmitter inputs. Detaching the cable
allows the receiver inputs to drop to an invalid level (GND),
so INVALID switches low and forces the RS-232 device to
power down. The ISL4270E remains powered down until the
cable is reconnected (INVALID = FORCEOFF = 1) and a
transition occurs on a receiver or transmitter input (see
Figure 5). For immediate power up when the cable is
reattached, connect FORCEON to FORCEOFF through a
network similar to that shown in Figure 3.
Capacitor Selection
The ISL4270E charge pumps require only 0.1
μF capacitors
for the full operational voltage range. Table 3 lists other
acceptable capacitor values for various supply voltage
ranges. Do not use values smaller than those listed in
Table 3. Increasing the capacitor values (by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption.
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1
μF bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple VCC to ground with a
capacitor of the same value as the charge-pump capacitor C1.
Connect the bypass capacitor as close as possible to the IC.
Transmitter Outputs when Exiting
Powerdown
Figure 8 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3k
Ω in parallel with 2500pF. Note
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
TABLE 3. REQUIRED CAPACITOR VALUES
VCC
(V)
C1
(
μF)
C2, C3, C4
(
μF)
3.0 to 3.6
0.1
4.5 to 5.5
0.047
0.33
3.0 to 5.5
0.22
1
RECEIVER
INPUTS
TRANSMITTER
OUTPUTS
INVALID
OUTPUT
V+
VCC
0
V-
tINVL
tINVH
FIGURE 7. ENHANCED AUTOMATIC POWERDOWN AND INVALID TIMING DIAGRAMS
TRANSMITTER
INPUTS
tWU
tAUTOPWDN
tWU
INVALID
REGION
}
ISL4270E
相關PDF資料 |
PDF描述 |
|---|---|
| PI90LV032AWEX | IC LINE DVR QUAD LVDS 3V 16-SOIC |
| PI90LV031AWEX | IC LINE DVR QUAD LVDS 3V 16-SOIC |
| V24B5M150BL3 | CONVERTER MOD DC/DC 5V 150W |
| MS3100E24-5P | CONN RCPT 16POS WALL MNT W/PINS |
| V24B5M150BL2 | CONVERTER MOD DC/DC 5V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL4270EIRZ-T | 功能描述:IC XMITTER/RCVR ESD RS232 32-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF) |
| ISL43110 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, SPST, High Performance Analog Switches |
| ISL43110_05 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low-Voltage, Single Supply, SPST, High Performance Analog Switches |
| ISL43110IB | 功能描述:IC SWITCH SPST 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
| ISL43110IB-T | 功能描述:IC SWITCH SPST 8SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 模擬開關，多路復用器，多路分解器 系列:- 標準包裝:48 系列:- 功能:開關 電路:4 x SPST - NO 導通狀態電阻:100 歐姆 電壓電源:單/雙電源 電壓 - 電源，單路/雙路(±):2 V ~ 12 V，±2 V ~ 6 V 電流 - 電源:50nA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。