- 您現在的位置：買賣IC網 > PDF目錄299231 > ISL3332IAZ-T (INTERSIL CORP) 3.3V, ±15kV ESD Protected, Two Port, Dual Protocol (RS-232/RS-485) Transceivers; Temperature Range: -40°C to 85°C; Package: 28-SSOP T&R PDF資料下載
參數資料
| 型號： | ISL3332IAZ-T |
| 廠商： | INTERSIL CORP |
| 元件分類： | Buffer和線驅動 |
| 英文描述： | 3.3V, ±15kV ESD Protected, Two Port, Dual Protocol (RS-232/RS-485) Transceivers; Temperature Range: -40°C to 85°C; Package: 28-SSOP T&R |
| 中文描述： | DUAL LINE TRANSCEIVER, PDSO28 |
| 封裝： | ROHS COMLIANT, PLASTIC, MO-150-AHB, SSOP-28 |
| 文件頁數： | 9/26頁 |
| 文件大?。?/td> | 946K |
| 代理商： | ISL3332IAZ-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
17
FN6362.0
May 27, 2008
below 115kbps can operate at the maximum length of 4000’
(1220m).
Higher data rates require faster edges, so both the ISL333X
versions offer an edge rate capable of 20Mbps data rates.
The ISL3333 also offers two slew rate limited edge rates to
minimize problems at slower data rates. Nevertheless, for
the best jitter performance when driving long cables, the
faster speed settings may be preferable, even at low data
rates. See the “RS-485 Slew Rate Limited Data Rates”
section for details.
Twisted pair is the cable of choice for RS-485/RS-422
networks. Twisted pair cables tend to pick up noise and
other electromagnetically induced voltages as common
mode signals, which are effectively rejected by the
differential receivers in these ICs.
The preferred cable connection technique is “daisy-
chaining”, where the cable runs from the connector of one
device directly to the connector of the next device, such that
cable stub lengths are negligible. A “backbone” structure,
where stubs run from the main backbone cable to each
device’s connector, is the next best choice, but care must be
taken to ensure that each stub is electrically “short”. See
Table 4 for recommended maximum stub lengths for each
speed option.
Proper termination is imperative to minimize reflections
when using the 20Mbps speed option. Short networks using
the medium and slow speed options need not be terminated,
but terminations are recommended unless power dissipation
is an overriding concern. Note that the RS-485 spec allows a
maximum of two terminations on a network, otherwise the Tx
output voltage may not meet the required VOD.
In point-to-point, or point-to-multipoint (RS-422) networks,
the main cable should be terminated in its characteristic
impedance (typically 120
Ω) at the end farthest from the
driver. In multi-receiver applications, stubs connecting
receivers to the main cable should be kept as short as
possible, but definitely shorter than the limits shown in Table
4. Multipoint (RS-485) systems require that the main cable
be terminated in its characteristic impedance at both ends.
Again, keep stubs connecting a transceiver to the main
cable as short as possible, and refer to Table 4. Avoid “star”,
and other configurations, where there are many “ends”
which would require more than the two allowed terminations
to prevent reflections.
High ESD
All pins on the ISL333X include ESD protection structures
rated at
±2.5kV (HBM), which is good enough to survive
ESD events commonly seen during manufacturing. But the
bus pins (Tx outputs and Rx inputs) are particularly
vulnerable to ESD events because they connect to an
exposed port on the exterior of the finished product. Simply
touching the port pins, or connecting a cable, can destroy an
unprotected port. ISL333X bus pins are fitted with advanced
structures that deliver ESD protection in excess of
±15kV
(HBM), without interfering with any signal in the RS-485 or
the RS-232 range. This high level of protection may
eliminate the need for board level protection, or at the very
least will increase the robustness of any board level scheme.
Small Packages
Competing 3.3V dual protocol ICs are available only in a 28
Ld SSOP. The ISL3333’s tiny 6x6mm QFN footprint is 80%
smaller than the competing SSOP.
Flow Through Pinouts
Even the ISL333X pinouts are features, in that the true
flow-through design simplifies board layout. Having the bus
pins all on one side of the package for easy routing to a
cable connector, and the Rx outputs and Tx inputs (logic
pins) on the other side for easy connection to a UART,
avoids costly and problematic crossovers. Competing “flow
through” pinouts mix logic and bus pin inputs on one side of
the package, and logic and bus pin outputs on the other side.
This forces the designer to route four traces from the right
side of the IC around the IC to the cable connector. Figure 11
illustrates the flow-through nature of the ISL333X’s pinout.
Low Power Shutdown (SHDN) Mode
The ON/OFF pin is driven low to place the IC (both ports) in
the SHDN mode, and the already low supply current drops to
as low as 21
μA. If this functionality isn’t desired, the pin can
be left disconnected (thanks to the internal pull-up), or it
should be connected to VCC (VL for the QFN), through a
1k
Ω resistor. SHDN disables the Tx and Rx outputs, and
disables the charge pumps if either port is in RS-232 mode,
so V+ collapses to VCC, and V- collapses to GND.
TABLE 4. RECOMMENDED STUB LENGTHS
SPEED OPTION
MAXIMUM STUB LENGTH
ft (m)
SLOW
350-500 (107-152)
MED
100-150 (30.5 - 46)
FAST
1-3 (0.3 - 0.9)
UART
OR
ASIC
OR
CONTROLLER
RA2
DY2
RA1
DY1
Z2
Y2
Y1
Z1
A1
B1
A2
B2
CON
N
E
C
T
O
R
ISL3332
FIGURE 11. ILLUSTRATION OF FLOW THROUGH PINOUT
D
R
ISL3332, ISL3333
相關PDF資料 |
PDF描述 |
|---|---|
| ISL3333IRZ | 3.3V, ±15kV ESD Protected, Two Port, Dual Protocol (RS-232/RS-485) Transceivers; Temperature Range: -40°C to 85°C; Package: 40-QFN |
| ISL3333IRZ-T | 3.3V, ±15kV ESD Protected, Two Port, Dual Protocol (RS-232/RS-485) Transceivers; Temperature Range: -40°C to 85°C; Package: 40-QFN T&R |
| ISL34340INZ | WSVGA 24-Bit Long-Reach Video Serdes with Bidirectional Side-Channel; Temperature Range: -40°C to 85°C; Package: 64-EPTQFP |
| ISL59604IRZ-T7A | SPECIALTY CONSUMER CIRCUIT, PQCC20 |
| ISL59604IRZ-T7 | SPECIALTY CONSUMER CIRCUIT, PQCC20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL3333 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Worlda??s Most Power-Effi cient |
| ISL3333EVAL1Z | 功能描述:EVAL BOARD 1 FOR ISL3333 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL3333IRZ | 功能描述:IC TXRX RS485/422 2PRT 40-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 產品目錄頁面:1402 (CN2011-ZH PDF) |
| ISL3333IRZ-T | 功能描述:IC TXRX RS485/422 2PRT 40-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISL3333IRZ-T7A | 功能描述:IC TXRX RS232/485 DL 2PRT 40QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:發射器 驅動器/接收器數:4/0 規程:RS422，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。