- 您現在的位置：買賣IC網 > PDF目錄385448 > IRPLDIM2E (International Rectifier) Digital Dimming DALI Ballast for 36W/T8 220V input PDF資料下載
參數資料
| 型號： | IRPLDIM2E |
| 廠商： | International Rectifier |
| 英文描述： | Digital Dimming DALI Ballast for 36W/T8 220V input |
| 中文描述： | 大理數字調光鎮流器36W/T8 220V輸入 |
| 文件頁數： | 8/13頁 |
| 文件大小： | 255K |
| 代理商： | IRPLDIM2E |
8
www.irf.com
IRPLDIM2E
Isolation and the Signals for DALI
The Digitally Addressable Lighting Interface is optically isolated from the microcontroller. Fig. 7 shows the connec-
tions between DALI and microcontroller.
The two wires from the DALI are converted to four signals. Two of the four are the transmit signal (RB2) and
receive signal (RX_DALI). The other two signals are the communications-enable (RB0) signal and the receive-
drive (RB1) signal. The transmit signal and the receive signal directly correlate to the levels seen on the Digitally
Addressable Lighting Interface. For receiving higher voltage logic on the DALI is translated to 5 volt logic at the
micro controller, and for transmission, the 5 volt logic is translated to the higher voltage logic on the DALI.
The ballast achieves very low power by controlling the communications circuit with the communication-enable
signal and the receive-drive signal. During normal operation the PIC16F628 enables the communication circuitry
with the communication-enable signal. With this signal there is enough current, less than 100uA, to indicate when
data is being sent to the ballast, but not enough current to accurately transfer the data. Upon detection (done by
a S/H built into the PIC16F628) the receive-drive is asserted to raise the current above 500uA to achieve good
signal transfer across the isolation. The receive-drive signal is only enabled long enough to transfer all the data;
then it is disabled (see waveforms in figure 8). This method strongly reduces the power/current use. The com-
parator built into the PIC16F628 is used to set the threshold for detection of the incoming data. The signal RA2 is
used as threshold for the comparator.
+
-
DALI
ENABLE
RB0
TX_DALI
RB2
RECEIVE-DRIVE
RB1
RA1
RA2
RX_DALI
MICRO-CONTROLLER
Fig. 7 DALI and Micro Controller connections
相關PDF資料 |
PDF描述 |
|---|---|
| IRS2001PBF | HIGH AND LOW SIDE DRIVER |
| IRS2001SPBF | HIGH AND LOW SIDE DRIVER |
| IRS2001STRPBF | HIGH AND LOW SIDE DRIVER |
| IRS2004PBF | HALF-BRIDGE DRIVER |
| IRS2004SPBF | HALF-BRIDGE DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRPLDIM2U | 功能描述:BALLAST DIM DIG 32W/T8 120VAC RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| IRPLDIM3 | 功能描述:電源管理IC開發工具 3 lvl Dim CFL Fluor Ballast w/IRS2158D RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLDIM4E | 功能描述:電源管理IC開發工具 Miniature Dimmable 26W Ballast dsgn kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLDIM5E | 功能描述:電源管理IC開發工具 4lvl Swtch Dim Fluor Ballast dsgn Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLHALO1E | 功能描述:電源管理IC開發工具 Halogen Cnvrtr 220/230VAC RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。