- 您現在的位置：買賣IC網 > PDF目錄384509 > IRPLDIM2a (Electronic Theatre Controls, Inc.) Digitally Addressable DALI Dimming Ballast Reference Design PDF資料下載
參數資料
| 型號： | IRPLDIM2a |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Digitally Addressable DALI Dimming Ballast Reference Design |
| 中文描述： | 大理數字可尋址調光鎮流器參考設計 |
| 文件頁數： | 8/15頁 |
| 文件大?。?/td> | 241K |
| 代理商： | IRPLDIM2A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
8
www.irf.com
IRPLDIM2a
Isolation and the Signals for DALI
The Digitally Addressable Lighting Interface is optically isolated from the microcontroller. Fig. 7 shows the connec-
tions between DALI and microcontroller.
The two wires from the DALI are converted to four signals. Two of the four are the transmit signal (RB2) and
receive signal (RX_DALI). The other two signals are the communications-enable (RB0) signal and the receive-
drive (RB1) signal. The transmit signal and the receive signal directly correlate to the levels seen on the Digitally
Addressable Lighting Interface. For receiving higher voltage logic on the DALI is translated to 5 volt logic at the
micro controller, and for transmission, the 5 volt logic is translated to the higher voltage logic on the DALI.
The ballast achieves very low power by controlling the communications circuit with the communication-enable
signal and the receive-drive signal. During normal operation the PIC16F628 enables the communication circuitry
with the communication-enable signal. With this signal there is enough current, less than 100uA, to indicate when
data is being sent to the ballast, but not enough current to accurately transfer the data. Upon detection (done by
a S/H built into the PIC16F628) the receive-drive is asserted to raise the current above 500uA to achieve good
signal transfer across the isolation. The receive-drive signal is only enabled long enough to transfer all the data;
then it is disabled (see waveforms in figure 8). This method strongly reduces the power/current use. The com-
parator built into the PIC16F628 is used to set the threshold for detection of the incoming data. The signal RA2 is
used as threshold for the comparator.
+
-
DALI
ENABLE
RB0
TX_DALI
RB2
RECEIVE-DRIVE
RB1
RA1
RA2
RX_DALI
MICRO-CONTROLLER
Fig. 7 DALI and Micro Controller connections
相關PDF資料 |
PDF描述 |
|---|---|
| IRPLLNR3 | Universal Input Linear Fluorescent Ballast using the IR2167 |
| IRPT1061A | Power Module for 1 hp Motor Drives |
| IRPT3054A | Power Module for 5 hp Motor Drives |
| IRPT5051C | Integrated Power Stage for 15 hp Motor Drives |
| IRPT5051D | Integrated Power Stage for 15 hp Motor Drives |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRPLDIM2E | 功能描述:KIT BALLAST DIM DIG 230VAC RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| IRPLDIM2U | 功能描述:BALLAST DIM DIG 32W/T8 120VAC RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| IRPLDIM3 | 功能描述:電源管理IC開發工具 3 lvl Dim CFL Fluor Ballast w/IRS2158D RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLDIM4E | 功能描述:電源管理IC開發工具 Miniature Dimmable 26W Ballast dsgn kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLDIM5E | 功能描述:電源管理IC開發工具 4lvl Swtch Dim Fluor Ballast dsgn Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。