- 您現在的位置：買賣IC網 > PDF目錄384483 > IMX29F002BPI-70 (Macronix International Co., Ltd.) 2M-BIT [256K x 8] CMOS FLASH MEMORY PDF資料下載
參數資料
| 型號： | IMX29F002BPI-70 |
| 廠商： | Macronix International Co., Ltd. |
| 英文描述： | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| 中文描述： | 200萬位[256K × 8]的CMOS閃存 |
| 文件頁數： | 4/49頁 |
| 文件大?。?/td> | 911K |
| 代理商： | IMX29F002BPI-70 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
4
REV. 1.1, JUN. 14, 2001
P/N: PM0547
MX29F002/002N
AUTOMATIC PROGRAMMING
The MX29F002T/B is byte programmable using the
Automatic Programming algorithm. The Automatic
Programming algorithm does not require the system to
time out or verify the data programmed. The typical
chip programming time of the MX29F002T/B at room
temperature is less than 3.5 seconds.
AUTOMATIC CHIP ERASE
Typical erasure at room temperature is accomplished
in less than 3 seconds. The device is erased using
the Automatic Erase algorithm. The Automatic Erase
algorithm automatically programs the entire array prior
to electrical erase. The timing and verification of
electrical erase are internally controlled by the device.
AUTOMATIC SECTOR ERASE
The MX29F002T/B is sector(s) erasable using MXIC's
Auto Sector Erase algorithm. Sector erase modes allow
sectors of the array to be erased in one erase cycle. The
Automatic Sector Erase algorithm automatically pro-
grams the specified sector(s) prior to electrical erase.
The timing and verification of electrical erase are inter-
nally controlled by the device.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm requires the
user to only write a program set-up commands include
2 unlock write cycle and A0H and a program command
(program data and address). The device automatically
times the programming pulse width, verifies the pro-
gram, and counts the number of sequences. A status
bit similar to DATA polling and a status bit toggling
between consecutive read cycles, provides feedback
to the user as to the status of the programming
operation.
MXIC's Automatic Erase algorithm requires the user to
write commands to the command register using stand-
ard microprocessor write timings. The device will
automatically pre-program and verify the entire array.
Then the device automatically times the erase pulse
width, verifies the erase, and counts the number of
sequences. A status bit similar to DATA polling and
status bit toggling between consecutive read cycles
provides feedback to the user as to the status of the
programming operation.
Commands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as inputs to an internal state-machine
which controls the erase and programming circuitry.
During write cycles, the command register internally
latches address and data needed for the programming
and erase operations. During a system write cycle,
addresses are latched on the falling edge, and data
are latched on the rising edge of WE .
MXIC's Flash technology combines years of EPROM
experience to produce the highest levels of quality, relia-
bility, and cost effectiveness. The MX29F002T/B electri-
cally erases all bits simultaneously using Fowler-Nord-
heim tunneling. The bytes are programmed one byte at
a time using the EPROM programming mechanism of hot
electron injection.
During a program cycle, the state-machine will control the
program sequences and command register will not re-
spond to any command set. During a Sector Erase cycle,
the command register will only respond to Erase Suspend
command. After Erase Suspend is completed, the device
stays in read mode. After the state machine has com-
pleted its task, it will allow the command register to
respond to its full command set.
AUTOMATIC ERASE ALGORITHM
相關PDF資料 |
PDF描述 |
|---|---|
| IMX29F002BTI-70 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| IMX29F002TQI-70 | 2M-BIT [256K x 8] CMOS FLASH MEMORY |
| IN4829 | STABISTORS Also, Tight Tolerance |
| IN4830 | STABISTORS Also, Tight Tolerance |
| IN5179 | STABISTORS Also, Tight Tolerance |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IMX29F002BTI-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
| IMX29F002TQI-70 | 制造商:MCNIX 制造商全稱:Macronix International 功能描述:2M-BIT [256K x 8] CMOS FLASH MEMORY |
| IMX2G-AG6-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:GENERAL PURPOSE DUAL TRANSISTOR |
| IMX2L-AG6-R | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:GENERAL PURPOSE DUAL TRANSISTOR |
| IMX2T108 | 功能描述:兩極晶體管 - BJT DUAL NPN 50V 150MA SOT-457 RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
發布緊急采購，3分鐘左右您將得到回復。